A new environmentally friendly method of photoreactive pressure-sensitive adhesives (PSAs) preparation was demonstrated. PSAs based on n-butyl acrylate (BA), acrylic acid (AA) and 4-acryloyloxy benxophenone (ABP) were prepared via the UV-induced cotelomerization process in the presence of a radical photoinitiator (acylphosphine oxide) and telogen (tetrabromomethane). Hydroxyterminated polybutadiene was used as a crosslinking agent. Influence of AA concentration (0–10 wt %) on kinetics of the cotelomerization process was investigated using a photodifferential scanning calorimetry method, selected physicochemical features of obtained photoreactive BA/AA/ABP cotelomers (molecular masses, polydispersity, monomers conversion and dynamic viscosity) and self-adhesive properties of obtained PSAs (adhesion, tack and cohesion) were studied, as well. It turned out that AA content is the important factor that influences monomers conversion (thereby the volatile parts content in prepolymer) and PSAs’ properties. As the acrylic acid content increases, the reaction rate increases, but the total monomers conversion and the solid content of the prepolymer decreases. Additionally, the adhesion and cohesion of PSAs were grown up, and their tackiness decreased. However, the AA content has no effect on molecular weights (Mw and Mn) and polydispersity (c.a. 1.5) of photoreactive cotelomers. The optimal AA content necessary to obtain a prepolymer with low volatile parts content and good PSA properties was determined.
A new method of solvent-free acrylic pressure-sensitive adhesives (PSAs) based on UV-induced cotelomerization products was presented. The key acrylic monomers (i.e., n-butyl acrylate and acrylic acid) with copolymerizable photoinitiator 4-acrylooxybenzophenone in the presence of a selected chain transfer agent (tetrabromomethane, TBM) were used in the UV-cotelomerization process. Moreover, two kinds of UV-photoinitiators (α-hydroxyalkylphenones, HPs and acylphosphine oxides, APOs) were tested. Photo-DSC, viscosity, thermogravimetric, and GPC measurements for cotelomers were performed. The kinetics study revealed that the systems with APOs, especially Omnirad 819 and Omnirad TPO, were characterized by a much higher reaction rate and greater initiation efficiency than HPs systems were. Additionally, the APO-based syrups exhibited a higher solid content (ca. 60–96 wt%), a higher dynamic viscosity (5–185 Pa·s), but slightly lower molecular weights (Mn and Mw) compared to HP syrups. However, better self-adhesive features (i.e., adhesion and tack) were observed for PSAs based on cotelomers syrups obtained using APOs with lower solid contents (55–80 wt%). It was found that as the solids content (i.e., monomers conversion) increased the adhesion, the tack and glass transition temperature decreased and the type and amount of photoinitiator had no effect on polydispersity. Most of the obtained PSAs were characterized by excellent cohesion, both at 20 °C and 70 °C.
New modifiers (i.e., acrylic syrups; ASs) of epoxy-resin-based thermally curable structural self-adhesive tapes (SATs) were prepared via a free radical bulk polymerization (FRBP) of n-butyl acrylate, butyl methacrylate, glycidyl methacrylate, and hydroxybutyl acrylate. In the process, two kinds of UV-photoinitiators (i.e., monoacylphosphine oxide/Omnirad TPO and bisacylphosphine oxide/Omnirad 819) and various mixing speed of the monomers mixture (200–1000 rpm) were applied. The TPO-based syrups exhibited a lower copolymers content (10–24 wt%), dynamic viscosity (<0.1 Pa·s), molecular weights (Mn and Mw, and polydispersity (1.9–2.5) than these with Omnirad 819. Additionally, the higher mixing speed significantly reduced monomers conversion and viscosity of ASs as well as molecular weights of the acrylate copolymers. These parameters influenced the properties of thermally uncured (e.g., adhesion) and thermally cured SATs (shear strength of aluminum/SAT/aluminum overlap joints). Better self-adhesive features were observed for SATs-TPO (based on ASs with lower monomers conversion, Mn and Mw); however, a slightly higher shear strength was noted for the thermally cured SAT-819 (ASs with higher monomers conversion, Mn and Mw). An impact of polydispersity of the acrylate copolymers as well as crosslinking degree of thermally cured SATs on the mechanical strength was also revealed.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.