Odd-impact exercise-loading was associated, similar to high-impact exercise-loading, with approximately 20% thicker cortex around the femoral neck. Since odd-impact exercises are mechanically less demanding to the body than high-impact exercises, it is argued that this type of bone training would offer a feasible basis for targeted exercise-based prevention of hip fragility.

Reproduction of the anatomical structures and functions of tissues using cells and designed 3D scaffolds is an ongoing challenge. For this, scaffolds with appropriate biomorphic surfaces promoting cell attachment, proliferation and differentiation are needed. In this study, eight triply-periodic minimal surface (TPMS)-based scaffolds were designed using specific trigonometric equations, providing the same porosity and the same number of unit cells, while presenting different surface curvatures. The scaffolds were fabricated by stereolithography using a photocurable resin based on the biocompatible, biodegradable and rubber-like material, poly(trimethylene carbonate) (PTMC). A numerical approach was developed to calculate the surface curvature distributions of the TPMS architectures. Moreover, the scaffolds were characterized by scanning electron microscopy, micro-computed tomography and water permeability measurements. These original scaffold architectures will be helpful to decipher the biofunctional role of the surface curvature of scaffolds intended for tissue engineering applications.

We examined how the cerebrospinal fluid (CSF) affects the distribution of electroencephalogram (EEG) measurement sensitivity. We used concentric spheres and realistic head models to investigate the difference between computed-tomography (CT) and magnetic resonance image (MRI) models that exclude the CSF layer. The cortical EEG sensitivity distributions support these phenomena and show that the CSF layer significantly influences them, thus identifying the importance of including the CSF layer inside the head volume conductor models. The results show that the highly conductive CSF channels the current, thus decreasing the maximum cortical current density relative to models that do not include the CSF. We found that the MRI and CT models yielded HSV results 20% and 45%, respectively, too small when compared with CSF-inclusive models.

No abstract

Pore space characteristics of biochars may vary depending on the used raw material and processing technology. Pore structure has significant effects on the water retention properties of biochar amended soils. In this work, several biochars were characterized with three-dimensional imaging and image analysis. X-ray computed microtomography was used to image biochars at resolution of 1.14 µm and the obtained images were analysed for porosity, pore-size distribution, specific surface area and structural anisotropy. In addition, random walk simulations were used to relate structural anisotropy to diffusive transport. Image analysis showed that considerable part of the biochar volume consist of pores in size range relevant to hydrological processes and storage of plant available water. Porosity and pore-size distribution were found to depend on the biochar type and the structural anisotopy analysis showed that used raw material considerably affects the pore characteristics at micrometre scale. Therefore attention should be paid to raw material selection and quality in applications requiring optimized pore structure.

No abstract

Typical silicate bioactive glasses are known to crystallize readily during the processing of porous scaffolds. While such crystallization does not fully suppress the bioactivity, the presence of significantly large amounts of crystals leads to a decrease in the rate of reaction of the glass and an uncontrolled release of ions. Furthermore, due to the non-congruent dissolution of silicate glasses, these materials have been shown to remain within the surgical site even 14 years postoperation. Therefore, a need for bioactive materials that can dissolve with higher conversion rates and more effectively are required. Within this work, boron was introduced, in the FDA approved S53P4 glass, at the expense of SiO2. The crystallization and sintering-ability of the newly developed glasses were investigated by differential thermal analysis. All the glasses were found to crystallize primarily from the surface, and the crystal phase precipitating was dependent upon the quantity of B2O3 incorporated. The rate of crystallization was found to be lower for the glasses were 25, 50 and 75 % of the SiO2 was replaced with B2O3. These glasses were further sintered into porous scaffolds using simple heat sintering. The impact of glass particles size and heat treatment temperature on the scaffolds porosity and average pore size was investigated. Scaffolds with porosity ranging from 10 to 60 % with compressive strength ranging from 1 to 35 MPa, were produced. The scaffolds remained amorphous during processing and their ability to rapidly precipitate hydroxycarbonated apatite was maintained. This is of particular interest in the field of tissue engineering as the scaffolds degradation and reaction was generally faster and offers higher controllability as opposed to current partially/fully crystallized scaffolds obtained from the FDA approved bioactive glasses. IntroductionAs of today, autografts are still the gold standard for the repair of large bone defects. However, with the aging and growing population, the number of surgical intervention to regenerate bone defects are increasing. The limited supply and patient site morbidity is a well-known disadvantage and problem [1][2]. Allografts are an option. However, the limited tissue bank as well as the higher risk for infection and cellular and humoral immune reactions limits their usage [3]. The quest for synthetic biomaterials to replace the autografts is more than two decades old. However, as of today no materials have shown as promising a result as autografts. Q. Chen et al. have reported the optimum characteristic that the synthetic materials should have to find great potential as bone grafts [4]. The bone graft should be a 3D construct (3D scaffold) not only biocompatible, but ultimately biodegradable and osteoconductive with highly interconnected porosity. Pore size should be no less than 100 µm to allow cell and fluid penetration as well as angiogenesis. In general, interconnected pores of at least 100 µm and an open porosity of over 50% is considered the minimum requirement for ti...

The purpose of this study was to investigate the potential of a novel recombinant human type II collagen/polylactide scaffold (rhCo-PLA) in the repair of full-thickness cartilage lesions with autologous chondrocyte implantation technique (ACI). The forming repair tissue was compared to spontaneous healing (spontaneous) and repair with a commercial porcine type I/III collagen membrane (pCo). Domestic pigs (4-month-old, n ¼ 20) were randomized into three study groups and a circular full-thickness chondral lesion with a diameter of 8 mm was created in the right medial femoral condyle. After 3 weeks, the chondral lesions were repaired with either rhCo-PLA or pCo together with autologous chondrocytes, or the lesion was only debrided and left untreated for spontaneous repair. The repair tissue was evaluated 4 months after the second operation. Hyaline cartilage formed most frequently in the rhCo-PLA treatment group. Biomechanically, there was a trend that both treatment groups resulted in better repair tissue than spontaneous healing. Adverse subchondral bone reactions developed less frequently in the spontaneous group (40%) and the rhCo-PLA treated group (50%) than in the pCo control group (100%). However, no statistically significant differences were found between the groups. The novel rhCo-PLA biomaterial showed promising results in this proof-of-concept study, but further studies will be needed in order to determine its effectiveness in articular cartilage repair. 2,3 However, the original ACI procedure where a periosteal flap covers the repair area has major intrinsic limitations, such as initial mechanical weakness of the repaired site and periosteal hypertrophy. 4A wide variety of biomaterials have been introduced for cartilage repair as periosteal flap substitutes in ACI.5-8 Our research group has developed a novel biomaterial scaffold rhCo-PLA, which is a biodegradable scaffold combining recombinant human type II collagen (rhCo) and polylactide 96/4 felt (PLA). Being free of animal products, rhCo-PLA scaffold eliminates the risk of undesirable immunological responses and transmission of animal-derived pathogens.9,10 We have demonstrated the biocompatibility and neocartilage forming ability of recombinant human type II collagen.11,12 Furthermore, the recombinant technology enables batch consistency and manufacture of high purity collagen. The synthetic polylactide can be fabricated into a 3D scaffold structure that provides the repair site with mechanical support while gradually degrading as neotissue forms. However, PLAs alone have limitations in bioactivity. This is typically seen as a dense connective tissue layer around the PLA. 13 The rhCo, in contrast, is incorporated in the synthetic PLA mesh to improve its physico-chemical and biomechanical characteristics. Collagen enhances hydrophilicity of a scaffold. 6,14 Mechanical loading pumps water out of cartilage tissue, and during unloading, the water is reabsorbed. Thus, the water reabsorbing ability is an essential characteristic of a scaffold. W...