Chamarro, J. (2014). Microsystem-assisted synthesis of carbon dots with fluorescent and colorimetric properties for pH detection. Nanoscale, 6, pp. 6018-6024. The present paper describes the use of a microfluidic system to synthesize carbon dots (Cdots) and their use as optical pH sensors. The synthesis is based on the thermal decomposition of ascorbic acid in dimethyl sulfoxide. The proposed microsystem is composed of a fluidic and a thermal platform, which enable proper control of synthesis variables. Uniform and monodispersed 3.3 nm-sized Cdots have been synthesized, the optical characterization of which showed their down/upconversion luminescence and colorimetric properties. The obtained Cdots have been used for pH detection with down and upconverison fluorescent properties as excitation sources. The naked eye or a photographic digital camera has also been implemented as detection systems with the hue parameter showing a linear pH range from 3.5 to 10.2. On the other hand, experiments on the cytotoxicity and permeability of the Cdots on human embryonic kidney cells revealed their adsorption on cells without causing any impact on the cellular morphology.The recent application of uorescent nanoparticles (NPs) such as quantum dots, dye-doped NPs and rare earth-based NPs in biomedical sensing and imaging has become a major subject of research over the last few years. Although a wide range of diverse photoluminescent NPs have been developed from new materials, an increased concern about their potential environmental and human health toxicity exists.1 Moreover, there are some NP-associated drawbacks such as modication of their surface for a particular function which involves highly timeconsuming processes.At the moment, one of the most attractive NPs are carbon dots (Cdots), which have recently had a major relevance in analytical and bioanalytical chemistry mainly due to their excellent luminescent properties and high biocompatibility as well as their low cost synthesis.2 However, although these Cdots are very promising NPs in nanotechnology and nanobiomedicine, much research needs to be done either to investigate their potential in sensor development or to identify novel synthesis approaches. In addition, Cdots show size dependent photoluminescence and upconversion luminescence properties leading to anti-Stokes type emissions.
While magnetic bead (MB)-based bioassays have been implemented in integrated devices, their handling on-chip is normally either not optimal--i.e. only trapping is achieved, with aggregation of the beads--or requires complex actuator systems. Herein, we describe a simple and low-cost magnetic actuator to trap and move MBs within a microfluidic chamber in order to enhance the mixing of a MB-based reaction. The magnetic actuator consists of a CD-shaped plastic unit with an arrangement of embedded magnets which, when rotating, generate the mixing. The magnetic actuator has been used to enhance the amplification reaction of an enzyme-linked fluorescence immunoassay to detect Escherichia coli O157:H7 whole cells, an enterohemorrhagic strain, which have caused several outbreaks in food and water samples. A 2.7-fold sensitivity enhancement was attained with a detection limit of 603 colony-forming units (CFU) /mL, when employing the magnetic actuator.
Photonic nanofences consisting of high aspect ratio polymeric optical subwavelength waveguides have been developed for their application into photonic sensing devices. They are up to millimeter long arrays of 250 nm wide and 6 μm high ridges produced by an advanced lithography process on a silicon substrate enabling their straightforward integration into complex photonic circuits. Both simulations and experimental results show that the overlap of the evanescent fields propagating from each photonic nanofence allows for the formation of an effective waveguide that confines the overall evanescent field within its limits. This permits a high interaction with the surrounding medium which can be larger than 90% of the total guided light intensity (approximately 20000 times larger than the evanescent field of a standard waveguide with equivalent dimensions). In this work, we not only investigate the photonic properties of these structures but also demonstrate their successful integration into a photonic sensor. An absorbance-based sensor for the determination of lead in water samples is therefore achieved by the combination of the photonic nanofences with an ion-sensitive optical membrane. The experimental results for lead detection in water show a sensitivity of 0.102 AU/decade, and a linear range between 10(-6) M and 10(-2) M Pb(II). A detection limit as low as 7.3 nM has been calculated according to IUPAC for a signal-to-noise ratio of 3.
A microfluidic system based on the low-temperature co-fired ceramics technology (LTCC) is proposed to reproducibly carry out a simple one-phase synthesis and functionalization of monodispersed gold nanoparticles. It takes advantage of the LTCC technology, offering a fast prototyping without the need to use sophisticated facilities, reducing significantly the cost and production time of microfluidic systems. Some other interesting advantages of the ceramic materials compared to glass, silicon or polymers are their versatility and chemical resistivity. The technology enables the construction of multilayered systems, which can integrate other mechanical, electronic and fluidic components in a single substrate. This approach allows rapid, easy, low cost and automated synthesis of the gold colloidal, thus it becomes a useful approach in the progression from laboratory scale to pilot-line scale processes, which is currently demanded.
A new type of absorbance-based optical sensor is presented. It is based on a chemical transduction membrane that acts simultaneously as the sensing element and as the light guiding medium. This membrane is inserted between two micromachined waveguides in a silica on silicon structure. Light propagates longitudinally through the membrane, which changes its spectral properties accordingly while interacting with the analyte. As the path length corresponds to the membrane length, not its thickness, high sensitivity can be achieved without an increase of the response time. This paper summarizes the design, the construction, and the validation results obtained with integrated waveguide absorbance optode (IWAO) prototypes. The main advantages of the reported optode are its simple configuration, high sensitivity, and versatility. Experimental results obtained with this IWAO, using a potassium-selective bulk optode, are shown and compared to those obtained with a conventional absorbance device incorporating the same membrane. The optimum membrane thickness of 4 µm gave the lowest light losses (15 dB). The absorbance sensitivities obtained (-0.86 AU/decade) were, as expected, higher than those shown by the conventional device (-0.03 AU/decade), with comparable response times (t 90% ) 0.5 min).
The first prototype of a technologically improved integrated waveguide absorbance optode (IWAO) was developed and tested with a membrane based on a new H+-selective ketocyanine dye and a cadmium ionophore. It was designed with curved instead of rectilinear planar waveguides. Results demonstrated the suitability of the new IWAOs to be employed as sensing platforms, which confer versatility, robustness, and mass production capabilities besides high sensitivity on conventional bulk optodes, as well as the usefulness of such dyes in developing ion-selective membranes in combination with a selective ionophore. The sensor integration as a detector in a flow injection system (FIA) was proposed to obtain an automated, simple, and sufficiently reproducible (RSD <5%) analytical methodology with a sample throughput of 55 h(-1). Very sensitive optodes were obtained, and detection limits on the order of 20 ppb were achieved. Because of the ionophore employed, the optode system showed excellent selectivity over alkali and alkaline-earth metals with the exception of samples containing lead and cadmium ions, where the membrane responded to both analytes. The proposed procedure combines all the advantages of the FIA systems, the simplicity of optical detection, ion recognition selectivity, and sensitivity of ketocyanine dyes, and the features achieved using the integrated device, which comprise an improved sensitivity and short response times as well as robustness, easy handling, and mass production.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.