The microclimate surrounding a plant has major effect on its health and photosynthesis process, where certain plants struggle in suboptimal environmental conditions and unbalanced levels of humidity and temperature. The ability to remotely track and correlate the effect of local environmental conditions on the healthy growth of plants can have great impact for increasing survival rate of plants and augmenting agriculture output. This necessitates the widespread distribution of lightweight sensory devices on the surface of each plant. Using flexible and biocompatible materials coupled with a smart compact design for a low power and lightweight system, we develop widely deployed, autonomous, and compliant wearables for plants. The demonstrated wearables integrate temperature, humidity and strain sensors, and can be intimately deployed on the soft surface of any plant to remotely and continuously evaluate optimal growth settings. This is enabled through simultaneous detection of environmental conditions while quantitatively tracking the growth rate (viz. elongation). Finally, we establish a nature-inspired origami-assembled 3D-printed "PlantCopter", used as a launching platform for our plant wearable to enable widespread microclimate monitoring in large fields.

Funding bodies included and grant numbers accurate Title of article OK All figures included Equations correct (symbols and sub/superscripts) Corrections should be made directly in the PDF file using the PDF annotation tools. If you have questions about this, please contact the editorial office. The corrected PDF and any accompanying files should be uploaded to the journal's Editorial Manager site.

A spiral interconnect array is a commonly used architecture for stretchable electronics, which accommodates large deformations during stretching. Here, we show the effect of different geometrical morphologies on the deformation behavior of the spiral island network. We use numerical modeling to calculate the stresses and strains in the spiral interconnects under the prescribed displacement of 1000 lm. Our result shows that spiral arm elongation depends on the angular position of that particular spiral in the array. We also introduce the concept of a unit-cell, which fairly replicates the deformation mechanism for full complex hexagon, diamond, and square shaped arrays. The spiral interconnects which are axially connected between displaced and fixed islands attain higher stretchability and thus experience the maximum deformations. We perform tensile testing of 3D printed replica and find that experimental observations corroborate with theoretical study.

The real-time monitoring of fluid properties in tubular systems, such as viscosity and flow rate, is essential for industries utilizing liquid mediums. Nowadays, most studies of the fluid characteristics are performed off-line using laboratory facilities that can provide accurate results, yet they do not match the demanded industrial pace. Off-line measurements are ineffective and time-consuming. The available real-time monitoring sensors for fluid properties are generally destructive methods that produce significant and persistent damage to the tubular systems during the installation process. Others use huge and bulky invasive instrument methods that generate considerable pressure reduction and energy loss in tubular systems. For these drawbacks, industries centered their attention on non-invasive and non-destructive testing (NDT) methodologies, which are installed on the outer tubular surface to avoid flow disturbance and desist shutting down systems for installations. Although these sensors showed excellent achievement for monitoring and inspecting pipe health conditions, the performance was not convincing for monitoring the properties of fluids. This review paper presents an overview of the real-time monitoring of fluid properties in tubular systems for industrial applications, particularly for pipe monitoring sensors, viscosity, and flow measurements. Additionally, the different available sensing mechanisms and their advantages, drawbacks, and potentials are discussed.

Real‐time monitoring of fluid viscosities in tubular systems is essential for industries transporting fluid media. The available real‐time viscometers for tubular systems have major drawbacks, such as using invasive methods with large pressure drops due to flow disturbances, destructive installation processes with permanent tube damage, and limited operability with laminar flows. Therefore, developing a viscometer to address the above‐mentioned concerns is required for industrial applications. In this study, a new application of a velocity‐dependent viscometer using a novel design for real‐time measurements with insignificant flow disruption is proposed. It involves a Poly (methyl‐methacrylate) microchannel bridge with a microfluidic flowmeter attached to a mechanically flexible Polydimethylsiloxane platform connected to the inner surface of the pipe, which can adapt to different pipe diameters and curvatures. Moreover, the proposed viscometer uses the pipe flow driving force to flow fluids into the microchannel for measurement without requiring a pumping system or any sample withdrawals. The results of the simulation analysis match the experimental results of the sensor performance. The sensor can measure different viscosities in the range of 4‐334 mPa s with a resolution higher than 2.7 mPa s. Finally, a stand‐alone system is integrated with the sensor for wireless data transmission.

Squamous cell carcinoma is a very common type of oral cancer that affects the health of people with an unacceptably high mortality rate attributed to the difficulties in detecting the disease at an early stage. Therefore, effective techniques for early diagnosis and effective therapy of oral cancer are necessary. In the present study, we exploit the ability of gold nanoparticles (AuNPs) to undergo coupled surface plasmon resonance when closely spaced to improve diagnosing squamous cell carcinoma of the tongue. The prepared AuNPs are characterized by UV–VIS spectroscopy, dynamic light scattering, Fourier transform infrared spectroscopy, and transmission electron microscopy. The size of the prepared AuNPs is 12 ± 2 nm with narrow size distributions and exhibited high stability with a zeta potential of − 16.5 mV. The light fluorescence of the normal and cancer cells is recorded before and after NP addition using a spectrometer upon excitation by 405-nm laser irradiation. Furthermore, the light reflectance of the examined samples is measured at different laser wavelengths (red to NIR region). The obtained results show that the cancer cells mixed with AuNPs produce a higher fluorescence peak at 489.2 nm than the cancer cells without AuNPs. Moreover, the optical diffuse reflectance analyses reveal that the addition of AuNPs enhances cancer detection especially at the 635-nm irradiation with sensitivity (94%), specificity (87%), and overall accuracy (91%).

No abstract

Flow sensors are essential for a variety of applications in fluidic industries. This paper proposes a liquid flow sensor using a microfluidic channel for macrotubular architectures. The sensor comprised a firm poly(methyl methacrylate) (PMMA) microfluidic channel bridge on a mechanically flexible polydimethylsiloxane (PDMS) platform installed on the inner wall of tubular systems. The flexible platform was compatible with various tubular architectures and adopted curvatures. In addition, the microscale fluidic channel surpassed the primary disadvantages of common bulky and rigid flowmeters that cause flow streams disturbance and significant pressure drops in tubular systems. Moreover, the microchannel flow sensor is based on detecting the dominated dynamic pressure generated from the fluid velocity inside the microchannel since the tube flow rate is proportional to the flow velocity inside the channel. The pressure sensors for the microchannel flowmeter displayed a sensitivity of 10 pF/kPa and were fabricated inside the PDMS platform. In particular, the pressure was measured using a capacitive pressure sensor owing to its compatibility with flexible electronics and low power consumption. The capacitive pressure sensor inside the microchannel measures the flowrate based on the force generated on the internal walls from the fluid flow velocity inside the channel. Furthermore, the flow sensor behavior was studied for the overall tubular system and validated using a simulation model for volume flow rate ranging from 500 to 2000 mL/min.