The Ohmically heated circular limiter tokamak ADITYA (R 0 =75 cm, a=25 cm) has been upgraded to a tokamak named the ADITYA Upgrade (ADITYA-U) with an open divertor configuration with divertor plates. The main goal of ADITYA-U is to carry out dedicated experiments relevant for bigger fusion machines including ITER, such as the generation and control of runaway electrons, disruption prediction, and mitigation studies, along with an improvement in confinement with shaped plasma. The ADITYA tokamak was dismantled and the assembly of ADITYA-U was completed in March 2016. Integration of subsystems like data acquisition and remote operation along with plasma production and preliminary plasma characterization of ADITYA-U plasmas are presented in this paper.

Since the 2018 IAEA-FEC conference, in addition to expanding the parameter horizons of the ADITYA-U machine, emphasis has been given to dedicated experiments on inductively driven particle injection (IPI) for disruption studies, runaway electron (RE) dynamics and mitigation, plasma rotation reversal, radiative-improved modes using Ne and Ar injection, modulation of magneto–hydrodynamic modes, edge turbulence using periodic gas puffs and electrode biasing (E-B). Plasma parameters close to the design parameters of circular plasmas with H2 and D2 as fuel have been realized, and the shaped plasma operation has also been initiated. Consistent plasma discharges having I P ∼ 100–210 kA, t ∼ 300–400 ms, n e ∼ 3–6 × 1019 m−3, core T e ∼ 300–500 eV were achieved with a maximum B T of ∼1.5 T. The enhanced plasma parameters are the outcome of repeated cycles of baking (135 °C), followed by extensive wall conditioning, which includes pulsed glow discharge cleaning in H, He and Ar–H mixture, and lithiumization. A higher confinement time has been observed in D2 compared to H2 plasmas. Furthermore, shaped plasmas are attempted for the first time in ADITYA-U. A first of its kind inductively driven particle injection for disruption mitigation studies has been developed and operated. The injection of solid particles into the plasma core leads to a fast current quench. Two pulses of electron cyclotron resonance wave at 42 GHz are launched in a single discharge: one pulse is used for pre-ionization and the second for heating. In a novel approach, a positively biased electrode is used to confine REs after discharge termination. E-B is also used for controlling the rotation of drift-tearing modes by changing the plasma rotation. Cold pulse propagation and signatures of detachment are observed during the injection of short gas puffs. A correlation between the plasma toroidal rotation and the total radiated power has been observed with neon gas injection-induced improved confinement modes.

No abstract

No abstract

In fusion devices, various techniques are employed for coating the plasma facing components (PFCs) including the vessel wall with low-Z material like lithium, boron, and silicon in order to enhance the plasma parameters and control. In ADITYA-Upgrade tokamak, different techniques of lithium wall conditioning are developed and implemented to obtain uniform and sustainable coating of Li on PFCs and the vessel wall. In this paper, two techniques used to generate Li from the source are reported. In one of the technique, a heated (fixed temperature of ∼120 °C) Li-rod is placed inside the hydrogen glow discharge cleaning (H-GDC) plasma and the sputtered Li by hydrogen (H) ions and atoms coats the wall and periphery. In the second technique, the Li is vapourized using a high-temperature Li-evaporator and released into the H-GDC plasma for uniform coating of Li on the PFCs and vessel. Significantly enhanced plasma parameters are obtained after Li coating by both techniques, with the evaporated Li performed better than the Li rod case. With the Li coating obtained with evaporated Li at 600 °C (550 mg Li) with H-GDC, the Li wall conditioning has been observed to be sustaining for in a larger number of plasma discharges in comparison to non-H-GDC assisted Li deposition. As the melting temperature of lithium hydride (LiH) is much higher (688.7 °C) than that of lithium (180.5 °C), this enhance the longer Li-coating lifetime relatively due to the formation of Li–H molecules on the vessel wall and PFCs. In ADITYA-U the carbon impurity and hydrogen recycling, due to relatively high surface area of graphite PFCs as well as their proximity to the plasma, limits the plasma performance and effective controls. Hence, H-GDC, H-GDC with Li-rod sputtering or Li evaporation, helium-GDC, argon–hydrogen mixtures-GDC in particular sequence are carried out to obtain better plasma discharges. The Li coating techniques and their effect on tokamak plasma discharges of ADITYA-U are discussed in this paper.