No abstract

No abstract

When mobile organisms are spatially disoriented, for instance by rapid repetitive movement, they must re-establish orientation. Past research has shown that the geometry of enclosing spaces is consistently used for reorientation by a wide variety of species, but that non-geometric features are not always used. Based on these findings, some investigators have postulated a species-universal 'geometric module' that is transcended by the acquisition of spatial language at 6 years. This conclusion has been challenged, however, by findings that children as young as 18 months actually do use features to reorient in larger enclosures than those used in the original experiments. The reason for the room size effect is explored here in five experiments. Collectively, the data on age at which features are first used point to the importance of both restriction of movement in the small space and the fact that features are closer in the small space. In addition, success is seen at younger ages when the target object is adjacent to the feature. These results favor an adaptive combination model of spatial reorientation over a 'module-plus-language' view.

The aim of the study was to develop a 3D computer model of the movement of a maxillary incisor tooth when subjected to an orthodontic load. A novel method was to be developed to directly and accurately measure orthodontic tooth movement in a group of human volunteers. This was to be used to validate the finite element-based computer model. The design took the form of a prospective experiment at a laboratory at the University of Wales in 1996/7. A laser apparatus was used to sample tooth movement every 0.01 seconds over a 1-minute cycle for 10 healthy volunteers, whilst a constant 0.39 N load was applied. This process was repeated on eight separate occasions and the most consistent five readings taken for each subject. Data were used to calculate the physical properties of the periodontal ligament (PDL). The data gleaned by this method were used to validate the 3D FEM model. This was formed of 15,000 four-noded tetrahedral elements. Tooth displacements ranged from 0.012 to 0.133 mm. An appropriate elastic modulus of 1 N/mm(2) and Poisson's Ratio of 0.45 was derived for the PDL. Strain analysis, using the model, suggested that a maximum PDL strain of 4.77 x 10(-3) was recorded at the alveolar crest, while the largest apical strain recorded was 1.55 x 10(-3). The maximum strains recorded in the surrounding alveolar bone were 35 times less than for the PDL. A novel method for direct measurement of PDL physical properties in the human subject has been developed. The validated FEM model lends further evidence that the PDL is the main mediator of orthodontic tooth movement.

No abstract

No abstract

No abstract

The objectives of the study were to isolate the bracket-cement interface, and to determine the influence of bracket base morphology and orthodontic bonding agent chosen on strength of adhesion. The bracket bases evaluated included 60, 80, and 100 single mesh bases, a double mesh base, and the Dynalock, and Mini Twin bases. The strength of interface provided by each of these bases with Concise, Transbond, Right On, and non-encapsulated Fuji Ortho LC cements, was measured in tension and recorded in Mega Pascals. The single-mesh bases performed well with either Concise or Right On (11*88-22*72 MPa) and, other than the 80-mesh bracket, relatively poorly with Transbond (2*18-5*15 MPa). With Fuji Ortho LC, the single mesh bases performed well (6*05-12*19 MPa). The double mesh base performed well with Right On (13*75 MPa), and reasonably well with Concise, Transbond, and Fuji Ortho LC (6*00-9*20 MPa). The Dynalock and Mini Twin Bases performed fairly well with all cements (8*87-17*16 MPa). It was concluded that the orthodontic bonding agent selected would appear to largely determine the bond strength achieved with a particular bracket base design. A definite trend was difficult to identify in this study, and it appeared that certain combinations of bracket base and bonding agent performed optimally. Particular base designs may allow improved adhesive penetration or improved penetration of curing light. Alternatively, the dimension and distribution of resin/cement tags prescribed by one base could promote a stress distribution that is better resisted by a particular adhesive.