Graphene quantum dots (GQDs), which are edge-bound nanometer-size graphene pieces, have fascinating optical and electronic properties. These have been synthesized either by nanolithography or from starting materials such as graphene oxide (GO) by the chemical breakdown of their extended planar structure, both of which are multistep tedious processes. Here, we report that during the acid treatment and chemical exfoliation of traditional pitch-based carbon fibers, that are both cheap and commercially available, the stacked graphitic submicrometer domains of the fibers are easily broken down, leading to the creation of GQDs with different size distribution in scalable amounts. The as-produced GQDs, in the size range of 1-4 nm, show two-dimensional morphology, most of which present zigzag edge structure, and are 1-3 atomic layers thick. The photoluminescence of the GQDs can be tailored through varying the size of the GQDs by changing process parameters. Due to the luminescence stability, nanosecond lifetime, biocompatibility, low toxicity, and high water solubility, these GQDs are demonstrated to be excellent probes for high contrast bioimaging and biosensing applications.

Atomic layers of two-dimensional (2D) materials have recently been the focus of extensive research. This follows from the footsteps of graphene, which has shown great potential for ultrathin optoelectronic devices. In this paper, we present a comprehensive study on the synthesis, characterization, and thin film photodetector application of atomic layers of InSe. Correlation between resonance Raman spectroscopy and photoconductivity measurements allows us to systematically track the evolution of the electronic band structure of 2D InSe as its thickness approaches few atomic layers. Analysis of photoconductivity spectra suggests that few-layered InSe has an indirect band gap of 1.4 eV, which is 200 meV higher than bulk InSe due to the suppressed interlayer electron orbital coupling. Temperature-dependent photocurrent measurements reveal that the suppressed interlayer interaction also results in more localized pz-like orbitals, and these orbitals couple strongly with the in-plane E' and E″ phonons. Finally, we measured a strong photoresponse of 34.7 mA/W and fast response time of 488 μs for a few layered InSe, suggesting that it is a good material for thin film optoelectronic applications.

We report the direct growth of large, atomically thin GaSe single crystals on insulating substrates by vapor phase mass transport. A correlation is identified between the number of layers and a Raman shift and intensity change. We found obvious contrast of the resistance of the material in the dark and when illuminated with visible light. In the photoconductivity measurement we observed a low dark current. The on-off ratio measured with a 405 nm at 0.5 mW/mm(2) light source is in the order of 10(3); the photoresponsivity is 17 mA/W, and the quantum efficiency is 5.2%, suggesting possibility for photodetector and sensor applications. The photocurrent spectrum of few-layer GaSe shows an intense blue shift of the excitation edge and expanded band gap compared with bulk material.

We have developed a synthetic gecko tape by transferring micropatterned carbon nanotube arrays onto flexible polymer tape based on the hierarchical structure found on the foot of a gecko lizard. The gecko tape can support a shear stress (36 N/cm 2 ) nearly four times higher than the gecko foot and sticks to a variety of surfaces, including Teflon. Both the micrometer-size setae (replicated by nanotube bundles) and nanometer-size spatulas (individual nanotubes) are necessary to achieve macroscopic shear adhesion and to translate the weak van der Waals interactions into high shear forces. We have demonstrated for the first time a macroscopic flexible patch that can be used repeatedly with peeling and adhesive properties better than the natural gecko foot. The carbon nanotube-based tape offers an excellent synthetic option as a dry conductive reversible adhesive in microelectronics, robotics, and space applications.adhesives ͉ nanomaterials ͉ hierarchical ͉ robotics F lexible adhesive tapes are indispensable in our daily lives, whether it is to leave a note to a friend or to seal packages. However, we rarely hang heavy objects on a wall using these tapes because the stickiness is time-and rate-dependent. The viscoelastic tapes do not work under vacuum, such as space applications, and where repeated attachment and detachment is required, such as wall-climbing robots. Nature has found an alternate solution to stick to surfaces without using sticky viscoelastic liquids. Natural selection has developed the wallclimbing lizard's foot (Fig. 1A) in a hierarchical structure, consisting of microscopic hairs called setae, which further split into hundreds of smaller structures called spatulas ( Fig. 1B) (1-4). On coming in contact with any surface, the spatulas deform, enabling molecular contact over large areas, thus translating weak van der Waals interactions into enormous attractive forces (4). There have been several theoretical models to elucidate the mechanism of gecko adhesion (5). However, it is not clear why nature has developed this intricate hierarchical structure of micrometer-size setae and nanometer-size spatulas on the gecko foot, instead of covering the whole feet with only setae or spatulas. Many synthetic structures using uniform polymer pillars and in some cases hierarchical structures (6, 7) have been constructed before, although the performance of these structures has not been as good as natural gecko (8, 9). One limitation of these polymer pillars with a high aspect ratio is that they are mechanically weak in comparison to keratin used in the natural foot-hairs.Here we have replicated the multiscale structure of setae and spatulas using microfabricated multiwalled carbon nanotubes and found that not only nanometer-length scales of spatulas (individual carbon nanotubes) but also micrometer-length scales of setae (patterns of carbon nanotubes) are important to support large shear forces. Our results show that a 1-cm 2 area of the carbon nanotube patterns transferred on a flexible tape (referred as a ''gec...

Atomically thin photodetectors based on 2D materials have attracted great interest due to their potential as highly energy-efficient integrated devices. However, photoinduced carrier generation in these media is relatively poor due to low optical absorption, limiting device performance. Current methods for overcoming this problem, such as reducing contact resistances or back gating, tend to increase dark current and suffer slow response times. Here, we realize the avalanche effect in a 2D material-based photodetector and show that avalanche multiplication can greatly enhance the device response of an ultrathin InSe-based photodetector. This is achieved by exploiting the large Schottky barrier formed between InSe and Al electrodes, enabling the application of a large bias voltage. Plasmonic enhancement of the photosensitivity, achieved by patterning arrays of Al nanodisks onto the InSe layer, further improves device efficiency. With an external quantum efficiency approaching 866%, a dark current in the picoamp range, and a fast response time of 87 μs, this atomic layer device exhibits multiple significant advances in overall performance for this class of devices.