Graphite oxide is one of the main precursors of graphene-based materials, which are highly promising for various technological applications because of their unusual electronic properties. Although epoxy and hydroxyl groups are widely accepted as its main functionalities, the complete structure of graphite oxide has remained elusive. By interpreting spectroscopic data in the context of the major functional groups believed to be present in graphite oxide, we now show evidence for the presence of five- and six-membered-ring lactols. On the basis of this chemical composition, we devised a complete reduction process through chemical conversion by sodium borohydride and sulfuric acid treatment, followed by thermal annealing. Only small amounts of impurities are present in the final product (less than 0.5 wt% of sulfur and nitrogen, compared with about 3 wt% with other chemical reductions). This method is particularly effective in the restoration of the π-conjugated structure, and leads to highly soluble and conductive graphene materials.

Graphene quantum dots (GQDs), which are edge-bound nanometer-size graphene pieces, have fascinating optical and electronic properties. These have been synthesized either by nanolithography or from starting materials such as graphene oxide (GO) by the chemical breakdown of their extended planar structure, both of which are multistep tedious processes. Here, we report that during the acid treatment and chemical exfoliation of traditional pitch-based carbon fibers, that are both cheap and commercially available, the stacked graphitic submicrometer domains of the fibers are easily broken down, leading to the creation of GQDs with different size distribution in scalable amounts. The as-produced GQDs, in the size range of 1-4 nm, show two-dimensional morphology, most of which present zigzag edge structure, and are 1-3 atomic layers thick. The photoluminescence of the GQDs can be tailored through varying the size of the GQDs by changing process parameters. Due to the luminescence stability, nanosecond lifetime, biocompatibility, low toxicity, and high water solubility, these GQDs are demonstrated to be excellent probes for high contrast bioimaging and biosensing applications.

Microscale supercapacitors provide an important complement to batteries in a variety of applications, including portable electronics. Although they can be manufactured using a number of printing and lithography techniques, continued improvements in cost, scalability and form factor are required to realize their full potential. Here, we demonstrate the scalable fabrication of a new type of all-carbon, monolithic supercapacitor by laser reduction and patterning of graphite oxide films. We pattern both in-plane and conventional electrodes consisting of reduced graphite oxide with micrometre resolution, between which graphite oxide serves as a solid electrolyte. The substantial amounts of trapped water in the graphite oxide makes it simultaneously a good ionic conductor and an electrical insulator, allowing it to serve as both an electrolyte and an electrode separator with ion transport characteristics similar to that observed for Nafion membranes. The resulting micro-supercapacitor devices show good cyclic stability, and energy storage capacities comparable to existing thin-film supercapacitors.

No abstract

Rapid progress in graphene-based applications is calling for new processing techniques for creating graphene components with different shapes, sizes, and edge structures. Here we report a controlled cutting process for graphene sheets, using nickel nanoparticles as a knife that cuts with nanoscale precision. The cutting proceeds via catalytic hydrogenation of the graphene lattice, and can generate graphene pieces with specifi c zigzag or armchair edges. The size of the nanoparticle dictates the edge structure that is produced during the cutting. The cutting occurs along straight lines and along symmetry lines, defined by angles of 60º or 120º, and is defl ected at free edges or defects, allowing practical control of graphene nano-engineering.

Micrometer-sized electrochemical capacitors have recently attracted attention due to their possible applications in micro-electronic devices. Here, a new approach to large-scale fabrication of high-capacitance, two-dimensional MoS2 film-based micro-supercapacitors is demonstrated via simple and low-cost spray painting of MoS2 nanosheets on Si/SiO2 chip and subsequent laser patterning. The obtained micro-supercapacitors are well defined by ten interdigitated electrodes (five electrodes per polarity) with 4.5 mm length, 820 μm wide for each electrode, 200 μm spacing between two electrodes and the thickness of electrode is ∼0.45 μm. The optimum MoS2 -based micro-supercapacitor exhibits excellent electrochemical performance for energy storage with aqueous electrolytes, with a high area capacitance of 8 mF cm(-2) (volumetric capacitance of 178 F cm(-3) ) and excellent cyclic performance, superior to reported graphene-based micro-supercapacitors. This strategy could provide a good opportunity to develop various micro-/nanosized energy storage devices to satisfy the requirements of portable, flexible, and transparent micro-electronic devices.

In this work, we present a synthesis approach for nitrogen-doped graphene-sheet-like nanostructures via the graphitization of a heteroatom polymer, in particular, polyaniline, under the catalysis of a cobalt species using multiwalled carbon nanotubes (MWNTs) as a supporting template. The graphene-rich composite catalysts (Co-N-MWNTs) exhibit substantially improved activity for oxygen reduction in nonaqueous lithium-ion electrolyte as compared to those of currently used carbon blacks and Pt/carbon catalysts, evidenced by both rotating disk electrode and Li-O(2) battery experiments. The synthesis-structure-activity correlations for the graphene nanostructures were explored by tuning their synthetic chemistry (support, nitrogen precursor, heating temperature, and transition metal type and content) to investigate how the resulting morphology and nitrogen-doping functionalities (e.g., pyridinic, pyrrolic, and quaternary) influence the catalyst activity. In particular, an optimal temperature for heat treatment during synthesis is critical to creating a high-surface-area catalyst with favorable nitrogen doping. The sole Co phase, Co(9)S(8), was present in the catalyst but plays a negligible role in ORR. Nevertheless, the addition of Co species in the synthesis is indispensable for achieving high activity, due to its effects on the final catalyst morphology and structure, including surface area, nitrogen doping, and graphene formation. This new route for the preparation of a nitrogen-doped graphene nanocomposite with carbon nanotube offers synthetic control of morphology and nitrogen functionality and shows promise for applications in nonaqueous oxygen reduction electrocatalysis for Li-O(2) battery cathodes.

Aqueous dispersions of graphene oxide (GO) have been found to emit a structured, strongly pH-dependent visible fluorescence. Based on experimental results and model computations, this is proposed to arise from quasi-molecular fluorophores, similar to polycyclic aromatic compounds, formed by the electronic coupling of carboxylic acid groups with nearby carbon atoms of graphene. Sharp and structured emission and excitation features resembling the spectra of molecular fluorophores are present near 500 nm in basic conditions. The GO emission reversibly broadens and red-shifts to ca. 680 nm in acidic conditions, while the excitation spectra remain very similar in shape and position, consistent with excited state protonation of the emitting species in acidic media. The sharp and structured emission and excitation features suggest that the effective fluorophore size in the GO samples is remarkably well defined.