Gliding birds continually change the shape and size of their wings, presumably to exploit the profound effect of wing morphology on aerodynamic performance. That birds should adjust wing sweep to suit glide speed has been predicted qualitatively by analytical glide models, which extrapolated the wing's performance envelope from aerodynamic theory. Here we describe the aerodynamic and structural performance of actual swift wings, as measured in a wind tunnel, and on this basis build a semi-empirical glide model. By measuring inside and outside swifts' behavioural envelope, we show that choosing the most suitable sweep can halve sink speed or triple turning rate. Extended wings are superior for slow glides and turns; swept wings are superior for fast glides and turns. This superiority is due to better aerodynamic performance-with the exception of fast turns. Swept wings are less effective at generating lift while turning at high speeds, but can bear the extreme loads. Finally, our glide model predicts that cost-effective gliding occurs at speeds of 8-10 m s(-1), whereas agility-related figures of merit peak at 15-25 m s(-1). In fact, swifts spend the night ('roost') in flight at 8-10 m s(-1) (ref. 11), thus our model can explain this choice for a resting behaviour. Morphing not only adjusts birds' wing performance to the task at hand, but could also control the flight of future aircraft.
A novel technique is proposed and investigated for the estimation of the body force field resulting from the operation of a dielectric barrier discharge plasma actuator. The technique relies on the measurement of the spatio-temporal evolution of the induced velocity field using high-speed particle image velocimetry (PIV). The technique has the advantage of providing spatial distribution of the body force vector field. A full Navier-Stokes term decomposition is applied on the evolving field along with additional closure norms in order to decouple the pressure gradient and body force terms. Results are compared with load-cell measurements of the direct reaction force and also momentum balance calculations based on the PIV field. Agreement between the different methods is observed. The data can easily be incorporated in computational flow solvers and also be used for validation and calibration of numerical plasma models.
An experimental analysis was performed of the unsteady aerodynamic loading caused by the impingement of a propeller slipstream on a downstream lifting surface. When installed on an aircraft, this unsteady loading results in vibrations that are transmitted to the fuselage and are perceived inside the cabin as structure-borne noise. A pylonmounted tractor-propeller configuration was installed in a low-speed wind tunnel at Delft University of Technology. Surface-microphone and particle-image-velocimetry measurements were taken to quantify the pressure fluctuations on the pylon and visualize the impingement phenomena. It was confirmed that the propeller tip vortex is the dominant source of pressure fluctuations on the pylon. Along the path of the tip vortex on the pylon, a periodic pressure response occurs with strong harmonics. The amplitude of the pressure fluctuations increases with increasing thrust setting, whereas the unsteady lift coefficient displays a nonmonotonic dependency on the propeller thrust. The lowest integral unsteady loads were obtained for cases with approximately integer ratios between the pylon chord and the wavelength of the perturbation associated with the propeller tip vortices. This implies that structure-borne-noise reductions might be obtained by matching the pylon chord with an integer multiple of the axial separation between the propeller tip vortices.
This paper addresses the aerodynamic performance and numerical modeling of overthe-wing propellers. Installing the propeller above a wing has the potential to increase wing lift-to-drag ratio, high-lift capabilities, and to reduce flyover noise. However, the prediction of its performance is difficult, since research on the aerodynamic interaction effects of over-the-wing propellers has been limited so far. For this reason, an exploratory wind tunnel campaign was performed with a wing featuring a fowler flap. A single propeller was installed above the wing at different chordwise locations and inclination angles. Wing surface-pressure and wake-pressure measurements showed strong, bilateral aerodynamic coupling between the propeller and wing. A configuration with the propeller attached to the flap showed wing lift increases of 8% and 3% in cruise and high-lift conditions, respectively. The key findings of the wind tunnel campaign were used to validate a low-fidelity numerical tool, which combines a non-uniform inflow blade-element model for the propeller, a panel method for the wing, and a vortex lattice model for the propeller slipstream. The numerical model was used to assess the effect of propeller axial location and diameter. Results indicated that the optimal axial propeller position is near the trailing edge of the wing, and that reducing the propeller diameter at constant thrust coefficient at this location is beneficial for distributed propulsion applications. The tool allows a rapid computation of over-the-wing propeller and wing performance in cruise conditions. This enables an efficient design space exploration during the conceptual design process of such configurations.
An experimental study of flow separation control with a nanosecond pulse plasma actuator was performed in wind-tunnel experiments. The discharge used had a pulse width of 12 ns and rising time of 3 ns with voltage up to 12 kV. Repetition frequency was adjustable up to 10 kHz. The first series of experiments was to measure integral effects of the actuator on lift and drag. Three different airfoil models were used, NACA-0015 with the chord of 20 cm, NLF-MOD22A with the chord of 60 cm and NACA 63-618 with the chord of 20 cm. Different geometries of the actuator were tested at flow speeds up to 80 m/s. In stall conditions the significant lift increase up to 20% accompanied by drag reduction (up to 3 times) was observed. The critical angle of attack shifted up to 5-7 degrees. The relation of the optimal discharge frequency to the chord length and flow velocity was proven. The dependence of the effect on the position of the actuator on the wing was studied, showing that the most effective position of the actuator is on the leading edge in case of leading edge separation. In order to study the mechanism of the nanosecond plasma actuation experiments using schlieren imaging were carried out. It shown the shock wave propagation and formation of large-scale vortex structure in the separation zone, which led to separation elimination. PIV diagnostics technique was used to investigate velocity field and quantitative properties of vortex formation. In flat-plate still air experiments small-scale actuator effects were investigated. Measured speed of flow generated by actuator was found to be of order of 0.1 m/s and a span-wise nonuniformity was observed. The experimental work is supported by numerical simulations of the phenomena. The formation of vortex similar to that observed in experiments was simulated in the case of laminar leading edge separation. Model simulations of free shear layer shown intensification of shear layer instabilities due to shock wave to shear layer interaction.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.