An experimental investigation of primary and secondary crossflow instability developing in the boundary layer of a 45 • swept wing, at a chord Reynolds number of 2.17·10 6 is presented. Linear stability theory is applied for preliminary estimation of the flow stability while surface flow visualisation using fluorescent oil is employed to inspect the topological features of the transition region. Hot-wire anemometry is extensively used for the investigation of the developing boundary layer and identification of the statistical and spectral characteristics of the instability modes. Primary stationary as well as unsteady type-I (z-mode), type-II (y-mode) and type-III modes are detected and quantified. Finally, three-component, three-dimensional measurements of the transitional boundary layer are performed using tomographic particle image velocimetry. This research presents the first application of an optical experimental technique for this type of flow. Among the optical techniques tomographic velocimetry represents, to date, the most advanced approach allowing the investigation of spatially correlated flow structures in threedimensional fields. Proper orthogonal decomposition (POD) analysis of the captured flow fields is applied to this goal. The first POD mode features a newly reported structure related to low-frequency oscillatory motion of the stationary vortices along the spanwise direction. The cause of this phenomenon is only conjectured. Its effect on transition is considered negligible but, given the related high energy level, it needs to be accounted for in experimental investigations. Secondary instability mechanisms are captured as well. The type-III mode corresponds to low frequency primary travelling crossflow waves interacting with the stationary ones. It appears in the inner upwelling region of the stationary crossflow vortices and is characterised by elongated structures approximately aligned with the axis of the stationary waves. The type-I secondary instability consists instead of significantly inclined structures located at the outer upwelling region of the stationary vortices. The much narrower wavelength and higher advection velocity of these structures correlate with the higher-frequency content of this mode. The results of the investigation of both primary and secondary instability from the exploited techniques agree with and complement each other and are in line with existing literature. Finally, they present the first experimental observation of the secondary instability structures under natural flow conditions.

A novel technique is proposed and investigated for the estimation of the body force field resulting from the operation of a dielectric barrier discharge plasma actuator. The technique relies on the measurement of the spatio-temporal evolution of the induced velocity field using high-speed particle image velocimetry (PIV). The technique has the advantage of providing spatial distribution of the body force vector field. A full Navier-Stokes term decomposition is applied on the evolving field along with additional closure norms in order to decouple the pressure gradient and body force terms. Results are compared with load-cell measurements of the direct reaction force and also momentum balance calculations based on the PIV field. Agreement between the different methods is observed. The data can easily be incorporated in computational flow solvers and also be used for validation and calibration of numerical plasma models.

The popularity of plasma actuators as flow control devices has sparked a flurry of diagnostic efforts towards their characterisation. This review article presents an overview of experimental investigations employing diagnostic techniques specifically aimed at AC dielectric barrier discharge, DC corona and nanosecond pulse plasma actuators. Mechanical, thermal and electrical characterisation techniques are treated. Various techniques for the measurement of induced velocity, body force, heating effects, voltage, current, power and discharge morphology are presented and common issues and challenges are described. The final part of this report addresses the effect of ambient conditions on the performance of plasma actuators.

No abstract

The steady and transient response of a laminar separation bubble to flow disturbances is examined experimentally. Wind tunnel experiments are performed on a NACA 0012 aerofoil at a chord Reynolds number of 130 000 and angle of attack of $2^{\circ }$. Under the investigated conditions, a laminar separation bubble forms on the suction side of the aerofoil in the unperturbed flow. Periodic disturbances are introduced into the boundary layer just upstream of separation by means of a surface-mounted dielectric barrier discharge plasma actuator. Two-component, time-resolved particle image velocimetry measurements are performed to characterise both quasi-steady and transient response of the flow to periodic disturbances. The results show that the dynamics of the laminar separation bubble is dominated by the periodic shedding of shear layer vortices, forming upstream of the mean reattachment location due to the amplification of unstable flow disturbances. Introducing the controlled perturbations leads to significant changes in separation bubble topology and the characteristics of the dominant coherent structures, with the effect dependent on both amplitude and frequency of disturbances. Linear stability analysis demonstrates that the induced changes to the mean bubble topology affect the stability characteristics, reducing the maximum growth rate and the frequency of the most amplified disturbances by 35 % and 20 %, respectively, when the bubble length is reduced by up to 40 %. The observed changes in stability characteristics are shown to correlate with the attendant variations in the shape factor. The transient response of the bubble is associated with significant changes in the separation bubble dynamics, with significant differences observed between the relative duration (${\approx}45\,\%$) of the transients flow response associated with the introduction and removal of the controlled disturbances. A detailed analysis of the results offers new insight into the response of laminar separation bubbles to changes in the disturbance environment.

Transition and flow development in a separation bubble formed on an airfoil are studied experimentally. The effects of tonal and broadband acoustic excitation are considered since such acoustic emissions commonly result from airfoil self-noise and can influence flow development via a feedback loop. This interdependence is decoupled, and the problem is studied in a controlled manner through the use of an external acoustic source. The flow field is assessed using time-resolved, two-component particle image velocimetry, the results of which show that, for equivalent energy input levels, tonal and broadband excitation can produce equivalent changes in the mean separation bubble topology. These changes in topology result from the influence of excitation on transition and the subsequent development of coherent structures in the bubble. Both tonal and broadband excitation lead to earlier shear layer roll-up and thus reduce the bubble size and advance mean reattachment upstream, while the shed vortices tend to persist farther downstream of mean reattachment in the case of tonal excitation. Through a cross-examination of linear stability theory (LST) predictions and measured disturbance characteristics, nonlinear disturbance interactions are shown to play a crucial role in the transition process, leading to significantly different disturbance development for the tonal and broadband excited flows. Specifically, tonal excitation results in transition being dominated by the excited mode, which grows in strong accordance with linear theory and damps the growth of all other disturbances. On the other hand, disturbance amplitudes are more moderate for the natural and broadband excited flows, and so all unstable disturbances initially grow in accordance with LST. For all cases, a rapid redistribution of perturbation energy to a broad range of frequencies follows, with the phenomenon occurring earliest for the broadband excitation case. By taking nonlinear effects into consideration, important ramifications are made clear in regards to comparing LST predictions and experimental or numerical results, thus explaining the trends reported in recent investigations. These findings offer new insights into the influence of tonal and broadband noise emissions, resulting from airfoil self-noise or otherwise, on transition and flow development within a separation bubble.

In the current study, selective forcing of cross-flow instability modes evolving on a 45• swept wing at Re = 2.17 · 10 6 is achieved by means of spanwise-modulated plasma actuators, positioned near the leading edge. In the perspective of laminar flow control, the followed methodology holds on the discrete roughness elements/upstream flow deformation (DRE/UFD) approach, thoroughly investigated by e.g. Saric et al. (1998);Malik et al. (1999) and Wassermann & Kloker (2002). The possibility of using active devices for UFD provides several advantages over passive means, allowing for a wider range of operating Re numbers and pressure distributions. In the present work, customised alternating current dielectric barrier discharge plasma actuators have been designed, manufactured and characterised. The authority of the actuators in forcing monochromatic stationary cross-flow modes at different spanwise wavelengths is assessed by means of infrared thermography. Moreover, quantitative spatio-temporal measurements of the boundary layer velocity field are performed using time-resolved particle image velocimetry. The results reveal distinct steady and unsteady forcing contributions of the plasma actuator on the boundary layer. It is shown that the actuators introduce unsteady fluctuations in the boundary layer, amplifying at frequencies significantly lower than the actuation frequency. In line with the DRE/UFD strategy, forcing a sub-critical stationary mode, with a shorter wavelength compared to the naturally selected mode, results in less amplified primary vortices and related fluctuations, compared to the critical forcing case. The effect of the forcing on the flow stability is further inspected by combining the measured actuators body-force with the numerical solution of the laminar boundary layer and linear stability theory. The simplified methodology yields fast and computationally cheap estimates on the effect of steady forcing (magnitude and direction) on the boundary layer stability.

This work investigates the three-dimensional, spatio-temporal flow development in the aft portion of a laminar separation bubble. The bubble is forming on a flat plate geometry, subjected to an adverse pressure gradient, featuring maximum reverse flow of approximately 2 % of the local free-stream velocity. Time-resolved velocity measurements are performed by means of planar and tomographic particle image velocimetry, in the vicinity of the reattachment region. The measurements are complemented with a numerical solution of the boundary layer equations in the upstream field. The combined numerical and measured boundary layer is used as a baseline flow for linear stability theory analysis. The results provide insight into the dynamics of dominant coherent structures that form in the separated shear layer and deform along the span. Stability analysis shows that the flow becomes unstable upstream of separation, where both normal and oblique modes undergo amplification. While the shear layer roll up is linked to the amplification of the fundamental normal mode, the oblique modes at angles lower than approximately $30^{\circ }$ are also amplified substantially at the fundamental frequency. A model based on the stability analysis and experimental measurements is employed to demonstrate that the spanwise deformations of rollers are produced due to a superposition of normal and oblique instability modes initiating upstream of separation. The degree of the initial spanwise deformations is shown to depend on the relative amplitude of the dominant normal and oblique waves. This is confirmed by forcing the normal mode through a controlled impulsive perturbation introduced by a spanwise invariant dielectric-barrier-discharge plasma actuator, resulting in the formation of spanwise coherent vortices. The findings elucidate the link between important features in the bubble shedding dynamics and stability characteristics and provide further clarification on the differences in the development of coherent structures seen in recent experiments. Moreover, the results present a handle on the development of effective control strategies that can be used to either promote or suppress shedding in separation bubbles, which is of interest for system performance improvement and control of aeroacoustic emissions in relevant applications.