Herein, it is demonstrated, by using industrial techniques, that a passivation layer with nanocontacts based on silicon oxide (SiOx) leads to significant improvements in the optoelectronical performance of ultrathin Cu(In,Ga)Se2 (CIGS) solar cells. Two approaches are applied for contact patterning of the passivation layer: point contacts and line contacts. For two CIGS growth conditions, 550 and 500 °C, the SiOx passivation layer demonstrates positive passivation properties, which are supported by electrical simulations. Such positive effects lead to an increase in the light to power conversion efficiency value of 2.6% (absolute value) for passivated devices compared with a nonpassivated reference device. Strikingly, both passivation architectures present similar efficiency values. However, there is a trade‐off between passivation effect and charge extraction, as demonstrated by the trade‐off between open‐circuit voltage (Voc) and short‐circuit current density (Jsc) compared with fill factor (FF). For the first time, a fully industrial upscalable process combining SiOx as rear passivation layer deposited by chemical vapor deposition, with photolithography for line contacts, yields promising results toward high‐performance and low‐cost ultrathin CIGS solar cells with champion devices reaching efficiency values of 12%, demonstrating the potential of SiOx as a passivation material for energy conversion devices.

In recent years, the strategies used to break the Cu(In,Ga)Se2 (CIGS) world record of light to power conversion efficiency, were based on improvements of the absorber optoelectronic and crystalline properties, mainly using complex post-deposition treatments. To reach even higher efficiency values, advances in the solar cell architecture are needed focusing in the CIGS interfaces. In this study, we evaluate the structural, morphological and optoelectronic impact on the CIGS properties of using an Al2O3 layer as a potential front passivation layer. The impact of Al2O3 tunnelling layer between CIGS and CdS is also addressed in this study. Morphological and structural analyses reveal that the use of Al2O3 alone is not detrimental to CIGS, although it does not resist to the CdS chemical bath deposition. When CdS is deposited on top of Al2O3, the CIGS optoelectronic properties are heavily degraded. Nonetheless, when Al2O3 is used alone, optoelectronic measurements reveal a positive impact of its inclusion such as a very low concentration of interface defects and the CIGS keeping the same recombination channels. With the findings of this study the best use of Al2O3 front passivation layer could be with alternative buffer layers. The Al2O3 layer will keep the CIGS surface with a low density of defects while keeping its structural and optoelectronic properties as good as the ones when CdS is deposited. It can also be reported that a comparison between the different analyses allowed us to strongly suggest for the first time that low-energy muon spin spectroscopy (LE-μSR) is sensitive to both charge carrier separation and bulk recombination in complex semiconductors.

The incorporation of nanostructures in optoelectronic devices for enhancing their optical performance is widely studied. However, several problems related to the processing complexity and the low performance of the nanostructures have hindered such actions in real‐life devices. Herein, a novel way of introducing gold nanoparticles in a solar cell structure is proposed in which the nanostructures are encapsulated with a dielectric layer, shielding them from high temperatures and harsh growth processing conditions of the remaining device. Through optical simulations, an enhancement of the effective optical path length of approximately four times the nominal thickness of the absorber layer is verified with the new architecture. Furthermore, the proposed concept in a Cu(In,Ga)Se2 solar cell device is demonstrated, where the short‐circuit current density is increased by 17.4%. The novel structure presented in this work is achieved by combining a bottom‐up chemical approach of depositing the nanostructures with a top‐down photolithographic process, which allows for an electrical contact.

Interface recombination in sub-µm optoelectronics has a major detrimental impact on devices' performance, showing the need for tailored passivation strategies to reach a technological boost. In this work, SiOx passivation based substrates were developed and integrated into ultrathin Cu(In,Ga)Se2 (CIGS) solar cells. This study aims to understand the impact of a passivation strategy, which uses several SiOx layer thicknesses (3, 8, and 25 nm) integrated into high performance substrates (HPS). The experimental study is complemented with 3D Lumerical finite-difference time-domain (FDTD) and 2D Silvaco ATLAS optical and electrical simulations, respectively, to perform a decoupling of optical and electronic gains, allowing for a deep discussion on the impact of the SiOx layer thickness in the CIGS solar cell performance. This study shows that as the passivation layer thickness increases, a rise in parasitic losses is observed. Hence, a balance between beneficial passivation and optical effects with harmful architectural constraints defines a threshold thickness to attain the best solar cell performance. Analyzing their electrical parameters, the 8 nm novel SiOx based substrate achieved a light to power conversion efficiency value of 13.2 %, a 1.3 % absolute improvement over the conventional Mo substrate (without SiOx).

Surface-enhanced Raman scattering (SERS) spectroscopy stands out due to its sensitivity, selectivity, and multiplex ability. The development of ready-to-use, simple, and low-cost SERS substrates is one of the main challenges of the field. In this paper, the intrinsic reproducibility of microfluidics technology was used for the fabrication of self-assembled nanoparticle structures over a paper film. The paper SERS substrates were fabricated by assembling anisotropic particles, gold nanostars (GNSs), and nanorods (NRs) onto paper to offer an extra enhancement to reach ultra-sensitive detection limits. A polydimethylsiloxane PDMS-paper hybrid device was used to control the drying kinetics of the nanoparticles over the paper substrate. This method allowed a high reproducibility and homogeneity of the fabrication of SERS substrates that reach limits of detection down to the picomolar range. This simple and low-cost fabrication of a paper-based sensing device was tested for the discrimination of different cell lineages.

Among the main challenges faced in cancer research, early detection, metastatic pathways and biomarker discovery are being tackled both by researchers and technology‐based companies. The development of novel technologies that can advance the state‐of‐the‐art for those defined challenges is critical in order to enhance the survival rates as well as to significantly lower cancer associated costs, not to mention social and human impact. In the recent years, the field of liquid biopsy has grown tremendously due to its capacity to obtain and study tumor material in a non‐invasive way. Liquid biopsy arises as an alternative diagnostic tool based on the analysis of biomarkers present in body fluids. The characterization of those biomarkers is commonly made by already well‐established standard technologies, usually limited in terms of sensitivity, selectivity, multiplexing, high‐throughput, and/or speed of analysis. Unfortunately, highly sensitive molecular diagnostic technologies still have high associated costs preventing their universal application. In this review, the authors aim to provide the reader with a general comprehension on how surface‐enhanced Raman scattering (SERS) spectroscopy can overcome those bottlenecks. The combination of SERS and liquid biopsy may fulfill the holy grail of the so‐called precision medicine, ultimately contributing to the dream of cancer chronification.

One of the trends making its way through the Photovoltaics (PV) industry, is the search for new application possibilities. Cu(In,Ga)Se2 (CIGS) thin film solar cells stand out due to their class leading power conversion efficiency of 23.35 %, flexibility, and low cost. The use of sub-µm ultrathin CIGS solar cells has been gaining prevalence, due to the reduction in material consumption and the manufacturing time. Precise CIGS finite-difference time-domain (FDTD) and 3D-drift diffusion baseline models were developed for the Lumerical suite and a 1D electrical model for SCAPS, allowing for an accurate description of the optoelectronic behavior and response of thin and ultrathin CIGS solar cells. As a result, it was possible to obtain accurate descriptions of the optoelectronic behavior of thin and ultrathin solar cells, and to perform an optical study and optimization of novel light management approaches, such as, random texturization, photonic nanostructures, plasmonic nanoparticles, among others. The developed light management architectures enabled to push the optical performance of an ultrathin solar cell and even surpass the performance of a thin film solar cell, enabling a short-circuit current enhancement of 6.15 mA/cm 2 over an ultrathin reference device, without any light management integrated.

In the universe of nanomaterials, silver nanoparticles (AgNPs) have attracted the attention of researchers because of their optical, catalytic, antimicrobial, fungicidal, and bactericidal properties. Recently, studies have correlated the toxicity and efficacy of antimicrobial activity with surface-volume ratio, morphology, polydispersity, ligand types, particle size, and stability of AgNPs. Soon, the need for characterization of properties such as diameter and polydispersity is clear. The methodologies conventionally used for characterization of AgNPs, although accurate, are generally expensive and laborious and can degrade the sample. Thus, the development of methodologies based on UV-Vis spectroscopy and chemometric techniques appears as an alternative for the characterization of diameter and polydispersity of the nanoparticles. For the development of the methodology in question, 50 samples were synthesized, varying the type, volume, and concentration of the reagents in order to increase the diameter and polydispersity values. All samples were analyzed by DLS and UV-Vis spectroscopy. For the construction of multivariate calibration models, the calibration and validation sets were selected using the SPXY algorithm, and their predictive capacity was evaluated based on the method figures. The model that presented the best predictive capacity was the one built with the pretreated spectra with the 1st derivative with a 15-point window and 2nd-order polynomial, providing prediction errors of 5.31% and 4.43% for diameter and polydispersity, respectively.