Design of new materials for nanostructured dye solar cells (DSC) requires understanding the link between the material properties and cell efficiency. This paper gives an overview of the fundamental and practical aspects of the modeling and characterization of DSCs, and integrates the knowledge into a user-friendly DSC device model. Starting from basic physical and electrochemical concepts, mathematical expressions for the IV curve and differential resistance of all resistive cell components are derived and their relation to electrochemical impedance spectroscopy (EIS) is explained. The current understanding of the associated physics is discussed in detail and clarified. It is shown how the model parameters can be determined from complete DSCs by current dependent EIS and incident-photon-to-collected-electron (IPCE) measurements, supplemented by optical characterization, and used to quantify performance losses in DSCs. The paper aims to give a necessary theoretical background and practical guidelines for establishing an effective feedback-loop for DSC testing and development.
Tools that assess the limitations of dye sensitized solar cells (DSSCs) made with new materials are critical for progress. Measuring the transient electrical signals (voltage or current) after optically perturbing a DSSC is an approach which can give information about electron concentration, transport and recombination. Here we describe the theory and practice of this class of optoelectronic measurements, illustrated with numerous examples. The measurements are interpreted with the multiple trapping continuum model which describes electrons in a semiconductor with an exponential distribution of trapping states. We review standard small perturbation photocurrent and photovoltage transients, and introduce the photovoltage time of flight measurement which allows the simultaneous derivation of both effective diffusion and recombination coefficients. We then consider the utility of large perturbation measurements such as charge extraction and the current interrupt technique for finding the internal charge and voltage within a device. Combining these measurements allows differences between DSSCs to be understood in terms such as electron collection efficiency, semiconductor conduction band edge shifts and recombination kinetics.
The suitability of stainless steel for dye solar cell substrate was investigated with respect to performance and stability using photovoltaic characterization, electrochemical impedance spectroscopy (EIS), open circuit voltage decay (OCVD), and substrate polarization measurements. Stainless steel was employed both as photoelectrode and as counter electrode substrate gaining initial cell efficiencies of 4.7% and 3.5%, respectively. The leakage current from the stainless steel substrate was found to be very low. The effect of the stainless steel substrate on the performance of the other cell components was also examined. The traditional data analysis based on external cell voltage was shown to be inadequate and even misleading. Here, the voltage over a single cell component was determined computationally on the basis of EIS measurements as a function of cell current; through this approach, we found that the stainless steel counter electrode did not have any impact on the photoelectrode whereas the stainless steel photoelectrode substrate decreased the effective electron lifetime and the recombination resistance of the dyed TiO 2 film.
Atomic layer deposited TiO 2 recombination blocking layers were prepared on ITO-PET photoelectrode substrates for dye solar cells and examined using several electrochemical methods. The blocking layers increased the open circuit voltage at low light intensities. At high light intensities decrease of the fill factor due to additional resistance of current transport through the layer was more significant than the positive effect by the reduced recombination. The decrease in the fill factor was reduced by thermal treatment that made the blocking layer more conductive due to a structural change from an amorphous to a crystalline form. Therefore, thinner blocking layers of this type are required for plastic cells prepared at low temperature than for conventional glass dye solar cells made with temperature processing.
In this study the stability of dye solar cells with different kinds of metals as the photoelectrode substrate is studied. Stainless steels, Inconel and titanium substrates were tested in order to find stable substrate options. Photovoltaic characterization, electrochemical impedance spectroscopy (EIS), scanning electron microscopy (SEM) and substrate polarization measurements were used in the characterization.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.