We experimentally demonstrate the use of a bulk-structured Bi(2)Te(3) topological insulator (TI) as an ultrafast mode-locker to generate femtosecond pulses from an all-fiberized cavity. Using a saturable absorber based on a mechanically exfoliated layer about 15 μm thick deposited onto a side-polished fiber, we show that stable soliton pulses with a temporal width of ~600 fs can readily be produced at 1547 nm from an erbium fiber ring cavity. Unlike previous TI-based mode-locked laser demonstrations, in which high-quality nanosheet-based TIs were used for saturable absorption, we chose to use a bulk-structured Bi(2)Te(3) layer because it is easy to fabricate. We found that the bulk-structured Bi(2)Te(3) layer can readily provide sufficient nonlinear saturable absorption for femtosecond mode-locking even if its modulation depth of ~15.7% is much lower than previously demonstrated nanosheet-structured TI-based saturable absorbers. This experimental demonstration indicates that high-crystalline-quality atomic-layered films of TI, which demand complicated and expensive material processing facilities, are not essential for ultrafast laser mode-locking applications.

We experimentally demonstrate a femtosecond mode-locked, all-fiberized laser that operates in the 2 μm region and that incorporates a saturable absorber based on a bulk-structured bismuth telluride (Bi(2)Te(3)) topological insulator (TI). Our fiberized saturable absorber was prepared by depositing a mechanically exfoliated, ~30 μm-thick Bi(2)Te(3) TI layer on a side-polished optical fiber platform. The bulk crystalline structure of the prepared Bi(2)Te(3) layer was confirmed by Raman and X-ray photoelectron spectroscopy measurements. The modulation depth of the prepared saturable absorber was measured to be ~20.6%. Using the saturable absorber, it is shown that stable, ultrafast pulses with a temporal width of ~795 fs could readily be generated at a wavelength of 1935 nm from a thulium/holmium co-doped fiber ring cavity. This experimental demonstration confirms that bulk structured, TI-based saturable absorbers can readily be used as an ultra-fast mode-locker for 2 μm lasers.

Dedicated multi-project wafer (MPW) runs for photonic integrated circuits (PICs) from Si foundries mean that researchers and small-to-medium enterprises (SMEs) can now afford to design and fabricate Si photonic chips. While these bare Si-PICs are adequate for testing new device and circuit designs on a probe-station, they cannot be developed into prototype devices, or tested outside of the laboratory, without first packaging them into a durable module. Photonic packaging of PICs is significantly more challenging, and currently orders of magnitude more expensive, than electronic packaging, because it calls for robust micron-level alignment of optical components, precise real-time temperature control, and often a high degree of vertical and horizontal electrical integration. Photonic packaging is perhaps the most significant bottleneck in the development of commercially relevant integrated photonic devices. This article describes how the key optical, electrical, and thermal requirements of Si-PIC packaging can be met, and what further progress is needed before industrial scale-up can be achieved.

Mono‐ and few‐layer transition metal dichalcogenides (TMDCs) have been widely used as saturable absorbers for ultrashort laser pulse generation, but their preparation is complicated and requires much expertise. The possible use of bulk‐structured TMDCs as saturable absorbers is therefore a very intriguing and technically important issue in laser technology. Here, for the first time, it is demonstrated that defective, bulk‐structured WTe2 microflakes can serve as a base saturable absorption material for fast mode‐lockers that can produce femtosecond pulses from fiber laser cavities. They have a modulation depth of 2.85%, from which stable laser pulses with a duration of 770 fs are readily obtained at a repetition rate of 13.98 MHz and a wavelength of 1556.2 nm, which is comparable to the performance achieved using mono‐ and few‐layer TMDCs. Density functional theory calculations show that the oxidative and defective surfaces of WTe2 microflakes do not degrade their saturable absorption performance in the near‐infrared range, allowing for a broad range of operative bandwidth. This study suggests that saturable absorption is an intrinsic property of TMDCs without relying on their structural dimensionality, providing a new direction for the development of TMDC‐based saturable absorbers.

We demonstrate the use of an all-fiberized, mode-locked 1.94 μm laser with a saturable absorption device based on a tungsten disulfide (WS2)-deposited side-polished fiber. The WS2 particles were prepared via liquid phase exfoliation (LPE) without centrifugation. A series of measurements including Raman spectroscopy, scanning electron microscopy (SEM), and atomic force microscopy (AFM) revealed that the prepared particles had thick nanostructures of more than 5 layers. The prepared saturable absorption device used the evanescent field interaction mechanism between the oscillating beam and WS2 particles and its modulation depth was measured to be ~10.9% at a wavelength of 1925 nm. Incorporating the WS2-based saturable absorption device into a thulium-holmium co-doped fiber ring cavity, stable mode-locked pulses with a temporal width of ~1.3 ps at a repetition rate of 34.8 MHz were readily obtained at a wavelength of 1941 nm. The results of this experiment confirm that WS2 can be used as an effective broadband saturable absorption material that is suitable to passively generate pulses at 2 μm wavelengths.