No abstract

Experimental and numerical studies are presented on the steady and unsteady radial forces produced in a single volute vaneless centrifugal pump. Experimentally, the unsteady pressure distributions were obtained using fast response pressure transducers. These measurements were compared with equivalent numerical results from a URANS calculation, using the commercial code FLUENT. Two impellers with different outlet diameters were tested for the same volute, with radial gaps between the blade and tongue of 10.0% and 15.8% of the impeller radius, for the bigger and smaller impeller diameters, respectively. Very often, pump manufacturers apply the similarity laws to this situation, but the measured specific speeds in this case were found to be slightly different. The steady radial forces for the two impellers were calculated from both the measured average pressure field and the model over a wide range of flow rates in order to fully characterize the pump behavior. Again, a deviation from the expected values applying the similarity laws was found. The data from the pressure fluctuation measurements were processed to obtain the dynamic forces at the blade passing frequency, also over a wide range of flow rates. Afterwards, these results were used to check the predictions from the numerical simulations. For some flow rates, the bigger diameter produced higher radial forces, but this was not to be a general rule for all the operating points. This paper describes the work carried out and summarizes the experimental and the numerical results, for both radial gaps. The steady and unsteady forces at the blade passing frequency were calculated by radial integration of the pressure distributions on the shroud side of the pump volute. For the unsteady forces, the numerical model allowed a separate analysis of the terms due to the pressure pulsations and terms related to the momentum exchange in the impeller. In this way, the whole operating range of the pump was studied and analyzed to account for the static and dynamic flow effects. The unsteady forces are very important when designing the pump shaft as they can produce a fatigue collapse if they are not kept under a proper working value.

An experimental investigation is presented which analyzes the unsteady pressure distribution existing in the volute of a conventional centrifugal pump with a nondimensional specific speed of 0.48, for flow-rates from 0% to 160% of the best-efficiency point. For that purpose, pressure signals were obtained at 36 different locations along the volute casing by means of fast-response pressure transducers. Particular attention was paid to the pressure fluctuations at the blade passage frequency, regarding both amplitude and phase delay relative to the motion of the blades. Also, the experimental data obtained was used to adjust the parameters of a simple acoustic model for the volute of the pump. The results clearly show the leading role played by the tongue in the impeller-volute interaction and the strong increase in the magnitude of dynamic forces and dipole-like sound generation in off-design conditions.

No abstract

No abstract

This paper presents the functional characterization of a centrifugal pump used as a turbine. It shows the characteristics of the machine involved at several rotational speeds, comparing the respective flows and heads. In this way, it is possible to observe the influence of the rotational speed on efficiency, as well as obtaining the characteristics at constant head and runaway speed. Also, the forces actuating on the impeller were studied. An uncertainty analysis was made to assess the accuracy of the results. The research results indicate that the turbine characteristics can be predicted to some extent from the pump characteristics, that water flows out of the runner free of swirl flow at the best efficiency point, and that radial stresses are lower than in pump mode

A study is presented on the fluid-dynamic pulsations and the corresponding dynamic forces generated in a centrifugal pump with single suction and vaneless volute due to blade-volute interaction. Four impellers with different outlet diameters, obtained from progressive cutbacks (trimmings) of the greatest one, were successively considered in the test pump, so that the radial gap between the impeller and the volute ranged from 8.8% to 23.2% of the impeller radius. The study was based on the numerical computation of the unsteady flow through the machine for a number of flow rates by means of the FLUENT code, solving the 3D unsteady Reynolds-averaged Navier–Stokes equations. Additionally, an experimental series of tests was conducted for the pump with one of the impellers, in order to obtain pressure fluctuation data along the volute front wall that allowed contrasting the numerical predictions. The data collected from the numerical computations were used to estimate the dynamic radial forces and torque at the blade-passing frequency, as a function of flow rate and blade-tongue radial gap. As expected, for a given impeller diameter, the dynamic load increases for off-design conditions, especially for the low range of flow rates, whereas the progressive reduction of the impeller-tongue gap brings about corresponding increments in dynamic load. In particular, varying the blade-tongue gap within the limits of this study resulted in multiplying the maximum magnitude of the blade-passing frequency radial force by a factor of about 4 for low flow rates (i.e., below the nominal flow rate) and 3 for high flow rates.

No abstract