The outermost layer of skin, stratum corneum (SC), functions as the major barrier to diffusion. SC has the architecture of dead keratin filled cells embedded in a lipid matrix. This work presents a detailed study of the hydration process in extracted SC lipids, isolated corneocytes and intact SC. Using isothermal sorption microcalorimetry and relaxation and wideline (1)H NMR, we study these systems at varying degrees of hydration/relative humidities (RH) at 25 degrees C. The basic findings are (i) there is a substantial swelling both of SC lipids, the corneocytes and the intact SC at high RH. At low RHs corneocytes take up more water than SC lipids do, while at high RHs swelling of SC lipids is more pronounced than that of corneocytes. (ii) Lipids in a fluid state are present in both extracted SC lipids and in the intact SC. (iii) The fraction of fluid lipids is lower at 1.4% water content than at 15% but remains virtually constant as the water content is further increased. (iv) Three exothermic phase transitions are detected in the SC lipids at RH=91-94%, and we speculate that the lipid re-organization is responsible for the hydration-induced variations in SC permeability. (v) The hydration causes swelling in the corneocytes, while it does not affect the mobility of solid components (keratin filaments).

Cystic fibrosis (CF) is a complex inherited disease which affects many organs, including the pancreas and liver, gastrointestinal tract and reproductive system, sweat glands and, particularly, the respiratory system. Pseudomonas aeruginosa is the main cause of chronic airway infection. In order to reduce morbidity and mortality due to lung infection by P. aeruginosa, aerosol antibiotics have been used to achieve high local concentrations in the airways and to reduce systemic toxicity. In the course of this review, the current treatments to control CF lung infections by P. aeruginosa are presented. Some innovative aerosol formulations such as liposomes and microspheres are herein reviewed, which may improve the efficiency of anti-pseudomonal agents, and ensure patients' compliance to treatments, by reducing dosing frequency and/or drug dose, while maintaining therapeutic efficacy, preventing the occurrence of bacterial resistance and/or reducing adverse effects due to their controlled-release properties.

In this work we present an analysis of the thermal behavior of hydroxypropylmethyl cellulose aqueous solutions, from room temperature to higher temperatures, above gelation. We focus on significant aspects, essentially overlooked in previous work, such as the correlation between polymer hydrophobicity and rheological behavior, and the shear effect on thermal gelation. Micropolarity and aggregation of the polymer chains were monitored by both UV/vis and fluorescence spectroscopic techniques, along with polarized light microscopy. Gel formation upon heating was investigated using rheological experiments, with both large strain (rotational) tests at different shear rates and small strain (oscillatory) tests. The present observations allow us to compose a picture of the evolution of the system upon heating: firstly, polymer reptation increases due to thermal motion, which leads to a weaker network. Secondly, above 55 • C, the polymer chains become more hydrophobic and polymer clusters start to form. Finally, the number of physical crosslinks between polymer clusters and the respective lifetimes increase and a three-dimensional network is formed. This network is drastically affected if higher shear rates, at nonNewtonian regimes, are applied to the system.

No abstract

In this work we use both model dependent and independent techniques to assess the difference between dissolution profiles in which ibuprofen, in the form of uncoated pellets, is used as a model drug. The choice of a proper regression function, the relevance of the estimated parameters and the influence of the choice of dissolution points in the assessment of differences is discussed. The results obtained via mean dissolution times (MDT) and fit-factors ( f and f ) are also discussed 1 2and a non-quantitative method based on profiles correlation with graphical representation (concentration vs. concentration and rate vs. rate) presented. The tested methods discriminate similarly between curves, although not in all cases, but those based on modeling, MDT and fit-factors have shown to be less informative than the correlation approach. 

The present work reports the study of different ketoprofen:excipient formulations, in order to determine the effect of the polymer substitution and type of diluent on the drug-release mechanism. Substituted cellulose-methylcellulose, hydroxypropylcellulose and hydroxypropylmethylcellulose were used as polymers, while lactose monohydrate and beta-cyclodextrin were tested as diluents. Distinct test formulations were prepared, containing 57.14% of ketoprofen, 20.00% of polymer, 20.29% of diluent, and 1.71% of talc/0.86% of magnesium stearate as lubricants. The tablets were tested for their drug content, weight variation, hardness, thickness, tensile strength, friability, swelling and release ratio. Polymers MC25 and HPC were found not to be appropriate for the preparation of modified release ketoprofen hydrophilic matrix tablets, while HPMC K15M and K100M showed to be advantageous. The analysis of the release profiles in the light of distinct kinetic models (zero-order, first-order, Higuchi and Korsmeyer-Peppas) led to the conclusion that the type of polymer did not influence the release mechanism of the drug. The mean dissolution time (MDT) was determined, the highest MDT value being obtained for HPMC formulations. Moreover, the drug-release process was found to be slightly influenced by the type of diluent, either lactose or beta-cyclodextrin.

No abstract

a b s t r a c tNovel chitosan based polyelectrolyte complexes (PEC) were developed and optimized in order to obtain films possessing the optimal functional properties (flexibility, resistance, water vapour transmission rate and bioadhesion) to be applied on skin. The development was based on the combination of chitosan and two polyacrylic acid (PAA) polymers with different crosslinkers and crosslinking densities. The interaction between the polymers was maximized controlling the pH, and by forming the films at a pH value close to the pK a of the respective components as identified by potentiometric and turbidimetric titrations. The action of glycerol, PEG200, Hydrovance and trehalose upon the functional properties of the films was also evaluated. Glycerol was found to improve the film properties in terms of flexibility, resistance and water vapour transmission rate (WVTR) with a maximum effect at 30%. The application of a pressure sensitive adhesive (PSA) significantly improved bioadhesion with a negligible influence in the resistance and flexibility of the films.The optimized film, including adhesive, has shown very good properties for application in the skin and represents a very promising formulation for further incorporation of drugs for topical and transdermal administration.