Hybrid energy generation models based on a variety of alternative energy supply technologies are considered the best way to cope with the depletion of fossil energy resources and to limit global warming. One of the currently missing technologies is the mimic of natural photosynthesis to convert carbon dioxide and water into chemical fuel using sunlight. This idea has been around for decades, but artificial photosynthesis of organic molecules is still far away from providing real-world solutions. The scientific challenge is to perform in an efficient way the multi-electron transfer reactions of water oxidation and carbon dioxide reduction using holes and single electrons generated in an illuminated semiconductor. In this tutorial review the design of photoelectrochemical (PEC) cells that combine solar water oxidation and CO2 reduction is discussed. In such PEC cells simultaneous transport and efficient use of light, electrons, protons and molecules has to be managed. It is explained how efficiency can be gained by compartmentalisation of the water oxidation and CO2 reduction processes by proton exchange membranes, and monolithic concepts of artificial leaves and solar membranes are presented. Besides transferring protons from the anode to the cathode compartment the membrane serves as a molecular barrier material to prevent cross-over of oxygen and fuel molecules. Innovative nano-organized multimaterials will be needed to realise practical artificial photosynthesis devices. This review provides an overview of synthesis techniques which could be used to realise monolithic multifunctional membrane-electrode assemblies, such as Layer-by-Layer (LbL) deposition, Atomic Layer Deposition (ALD), and porous silicon (porSi) engineering. Advances in modelling approaches, electrochemical techniques and in situ spectroscopies to characterise overall PEC cell performance are discussed.

Synthetic methods that allow for the controlled design of well-defined Pt nanoparticles are highly desirable for fundamental catalysis research. In this work, we propose a strategy that allows precise and independent control of the Pt particle size and coverage. Our approach exploits the versatility of the atomic layer deposition (ALD) technique by combining two ALD processes for Pt using different reactants. The particle areal density is controlled by tailoring the number of ALD cycles using trimethyl(methylcyclopentadienyl)platinum and oxygen, while subsequent growth using the same Pt precursor in combination with nitrogen plasma allows for tuning of the particle size at the atomic level. The excellent control over the particle morphology is clearly demonstrated by means of in situ and ex situ X-ray fluorescence and grazing incidence small angle X-ray scattering experiments, providing information about the Pt loading, average particle dimensions, and mean center-to-center particle distance.

A system is demonstrated that autonomously produces hydrogen gas using sunlight and outside air as the only inputs. Oxygen and hydrogen formation reactions occur on either side of a monolithic "solar membrane" inserted in a two-compartment photoelectrochemical cell. A surface film of Nafion (R) serves as a solid electrolyte. This proof of concept invites further development of air-based cells

Solar hydrogen devices combine the power of photovoltaics and water electrolysis to produce hydrogen in a hybrid form of energy production. To engineer these into integrated devices (i.e. a water splitting catalyst on top of a PV element), the need exists for thin film catalysts that are both transparent for solar light and efficient in water splitting. Manganese oxides have already been shown to exhibit good water splitting performance, which can be further enhanced by conformal coating on high surface-area structures. The latter can be achieved by atomic layer deposition (ALD). However, to optimize the catalytic and transparency properties of the water splitting layer, an excellent control over the oxidation state of the manganese in the film is required. So far MnO, Mn3O4 and MnO2 ALD have been shown, while Mn2O3 is the most promising catalyst. Therefore, we investigated the post-deposition oxidation and reduction of MnO and MnO2 ALD films, and derived strategies to achieve every phase in the MnO-MnO2 range by tuning the ALD process and post-ALD annealing conditions. Thin film Mn2O3 is obtained by thermal reduction of ALD MnO2, without the need for oxidative high temperature treatments. The obtained Mn2O3 is examined for solar water splitting devices, and compared to the as-deposited MnO2. Both thin films show oxygen evolution activity and good solar light transmission

Water splitting was performed in a photoelectrochemical cell (PEC) with water oxidation and hydrogen formation reactions in two separate compartments. A photoanode consisting of carbon paper loaded with TiO2 and a cathode made of Pt dispersed on carbon black spread also on carbon paper were fixed on both sides of a Nafion® membrane and electrically coupled via an external circuit. Anode and cathode compartments with serpentine flow field were operated either in the liquid or vapour phase. Electrical current was monitored with chronoamperometry and D2 formation from deuterated water using mass spectrometry. Mapping the photocurrent under a variety of reaction conditions enabled identification of the limiting factors related to proton and photocarrier transport and reaction product evacuation. This comprehensive research approach to the operation of a PEC will assist future optimisation of cell design and development of membrane electrode assemblies.

Solving the water scarcity problem by enhancing water extraction from air technology.

A vapor-fed solar hydrogen generator with KOH-doped poly(vinyl alcohol) anion exchange membrane flanked with NiFe and NiMo catalysts is demonstrated.

Metal halide perovskites are actively pursued as photoelectrodes to drive solar fuel synthesis. However, currently, these photocathodes suffer from limited stability in water, which hampers their practical application. Here, we report a high-performance solution-processable photocathode composed of cesium formamidinium methylammonium triple-cation lead halide perovskite protected by an Al-doped ZnO (AZO) layer combined with a Field’s metal encapsulation. Careful selection of charge transport layers resulted in an improvement in photocurrent, fill factor, device stability and reproducibility. The dead pixels count reduced from 25 to 6% for the devices with an AZO layer, and in photocathodes with an AZO layer the photocurrent density increased by almost 20% to 14.3 mA cm–2. In addition, we observed a 5-fold increase in the device lifetime for photocathodes with AZO, which reached up to 18 h before complete failure. Finally, the photocathodes are fabricated using low-cost and scalable methods, which have promise to become compatible with standard solution-based processes.