Force touch sensors have received a great deal of attention for various applications owing to their versatile ability to detect touch and pressure. To demonstrate high‐performance force touch sensors, numerous studies have been performed, focusing on high sensitivity, transparency, and mechanical durability against bending. However, it is still challenging to apply force touch sensors in flexible applications, because their sensing performance is subject to change and degraded by induced mechanical stress and deformation when the device is bent. Here, a high‐performance and transparent nanoforce touch sensor with bending‐insensitivity is reported. This is achieved by developing a thin, flexible, and transparent hierarchical nanocomposite film, which is composed of a nanostructured plastic base, coplanar electrodes, and a dielectric polymer layer with silver nanoparticles. The fabrication process is simple that high manufacturing repeatability, uniformity, and reliability are achieved on a large‐area (8 in.) scale. The fabricated device shows a pressure sensitivity of 0.036 kPa−1 with high transparency (83%) in a pressure range up to 3 kPa. In particular, its thin thickness (45 µm) and the coplanar electrode enable to achieve excellent insensitivity to the bending with a radius of curvature of 4 mm more than 10 000 times.

The correlation of microstructure and Charpy V-notch (CVN) impact properties of a high-toughness API X70 pipeline steel was investigated in this study. Six kinds of steel were fabricated by varying the hot-rolling conditions, and their microstructures, effective grain sizes, and CVN impact properties were analyzed. The CVN impact test results indicated that the steels rolled in the single-phase region had higher upper-shelf energies (USEs) and lower energy-transition temperatures (ETTs) than the steels rolled in the two-phase region because their microstructures were composed of acicular ferrite (AF) and fine polygonal ferrite (PF). The decreased ETT in the steels rolled in the single-phase region could be explained by the decrease in the overall effective grain size due to the presence of AF having a smaller effective grain size. On the other hand, the absorbed energy of the steels rolled in the twophase region was considerably lower because a large amount of dislocations were generated inside PFs during rolling. It was further decreased when coarse martensite or cementite was formed during the cooling process.

Nanowire (NW) transfer technology has provided promising strategies to realize future flexible materials and electronics. Using this technology, geometrically controlled, high-quality NW arrays can now be obtained easily on various flexible substrates with high throughput. However, it is still challenging to extend this technology to a wide range of high-performance device applications because its limited temperature tolerance precludes the use of high-temperature annealing, which is essential for NW crystallization and functionalization. A pulsed laser technique has been developed to anneal NWs in the presence of a flexible substrate; however, the induced temperature is not high enough to improve the properties of materials such as ceramics and semiconductors. Here, we present a versatile nanotransfer method that is applicable to NWs that require high-temperature annealing. To successfully anneal NWs during their transfer, the developed fabrication method involves sequential removal of a nanoscale sacrificial layer. Using this method, we first produce an ultralong, perfectly aligned polycrystalline barium titanate (BaTiO) NW array that is heat treated at 700 °C on a flexible polyethylene terephthalate (PET) substrate. This high-quality piezoelectric NW array on a flexible substrate is used as a flexible nanogenerator that generates current and voltage 37 and 10 times higher, respectively, than those of a nanogenerator made of noncrystallized BaTiO NWs.

No abstract

Correlation of rolling conditions, microstructure, and low-temperature toughness of high-toughness X70 pipeline steels was investigated in this study. Twelve kinds of steel specimens were fabricated by vacuum-induction melting and hot rolling, and their microstructures were varied by rolling conditions. Charpy V-notch (CVN) impact test and drop-weight tear test (DWTT) were conducted on the rolled steel specimens in order to analyze low-temperature fracture properties. Charpy impact test results indicated that the energy transition temperature (ETT) was below Ϫ100 °C when the finish cooling temperature range was 350 °C to 500 °C, showing excellent low-temperature toughness. The ETT increased because of the formation of bainitic ferrite and martensite at low finish cooling temperatures and because of the increase in effective grain size due to the formation of coarse ferrites at high finish cooling temperatures. Most of the specimens also showed excellent DWTT properties as the percent shear area well exceeded 85 pct, irrespective of finish rolling temperatures or finish cooling temperatures, although a large amount of inverse fracture occurred at some finish cooling temperatures.

No abstract

This study proposes a reliable and self-powered hydrogen (H 2 ) gas sensor composed of a chemo-mechanically operating nanostructured film and photovoltaic cell. Specifically, the nanostructured film has a configuration in which an asymmetrically coated palladium (Pd) film is coated on a periodic polyurethane acrylate (PUA) nanograting. The asymmetric Pd nanostructures, optimized by a finite element method simulation, swell upon reacting with H 2 and thereby bend the PUA nanograting, changing the amount of transmitted light and the current output of the photovoltaic cell. Since the degree of warping is determined by the concentration of H 2 gas, a wide concentration range of H 2 (0.1−4.0%) can be detected by measuring the self-generated electrical current of the photovoltaic cell without external power. The normalized output current changes are ∼1.5%, ∼2.8%, ∼3.5%, ∼5.0%, ∼21.5%, and 25.3% when the concentrations of H 2 gas are 0.1%, 0.5%, 1.0%, 1.6%, 2%, and 4%, respectively. Moreover, because Pd is highly chemically reactive to H 2 and also because there is no electrical current applied through Pd, the proposed sensor can avoid device failure due to the breakage of the Pd sensing material, resulting in high reliability, and can show high selectivity against various gases such as carbon monoxide, hydrogen sulfide, nitrogen dioxide, and water vapor. Finally, using only ambient visible light, the sensor was modularized to produce an alarm in the presence of H 2 gas, verifying a potential always-on H 2 gas monitoring application.

Biodegradable or eco-degradable electronics is an emerging field of technology capable of reducing the excessively increasing electronic waste originating from the rapid development of personalized and bio-integrated devices and skin adhesive patches. Through an advantageous solution process, biodegradable conductive pastes can be employed in various applications of soft and flexible devices. Herein a biodegradable conductive paste composed of molybdenum (Mo) microparticles and polybutylene adipate terephthalate (PBAT) exhibiting excellent mechanical flexibility and stretchability is reported, while also demonstrating substantially superior mechanical and conductive properties compared with previously reported biodegradable polymer matrices such as poly butanedithiol 1,3,5-triallyl-1,3,5-triazine-2,4,6-(1H,3H,5H)-trione pentenoic anhydride (PBTPA) and Candelilla wax (CW) owing to the significant elongation of PBAT. Moderate dissolution in phosphate buffer saline (PBS) accomplishes its full biodegradability and programmable lifecycle. Tetraglycol (TG) enhances elongation and conductivity performance by acting as a lubricant and improving the dispersion of microparticles. The practical implications of the Mo/PBAT pastes are demonstrated in numerous biodegradable electronic applications such as electrodes, strain and temperature sensors, joule heaters, interconnectors, and freestanding radiofrequency (RF) coils.