______________________________________________________________________ AbstractPolydimethylsiloxane, also known as PDMS, has been widely used in the biomedical industry because of its biocompatible material and its biomechanical behavior is similar to biological tissues, with applications in the study of aneurysmal behavior and devices such as: Micro pumps, optical systems, microfluidic circuits. Many advances in research have been reached, but further tests are still necessary to understand the mechanical behavior and applicability of the material. For the study of PDMS behavior, two different techniques are employed: numerical and experimental. In experimental studies, it is extremely popular to use a field technique, in which the most appropriate technique to measure the field displacement of PDMS, without decorrelation, is the Digital Image Correlation (DIC) method. In this paper, we revised the most important experimental works with PDMS material Review Article

Overall, this review aims at presenting a helpful guidance to the engineering and design of optical microsystems for optogenetic applications.

No abstract

Three-dimensional (3D) printed poly(ε-caprolactone) (PCL) based scaffolds have being proposed for different tissue engineering applications. This study addresses the design and fabrication of 3D PCL constructs with different struts alignments at 90°, 45° and 90° with offset. The morphology and the mechanical behavior under uniaxial compressive load were assessed at different strain percentages. The combination of a new compressionCT device and micro computed tomography (micro-CT) allowed understanding the influence of pore geometry under controlled compressive strain in the mechanical and structural behavior of PCL constructs. Finite element analysis (FEA) was applied using the micro-CT data to modulate the mechanical response and compare with the conventional uniaxial compression tests. Scanning electron microscopic analysis showed a very high level of reproducibility and a low error comparing with the theoretical values, confirming that the alignment and the dimensional features of the printed struts are reliable. The mechanical tests showed that the 90° architecture presented the highest stiffness. With the compressionCT device was observed that the 90° and 90° with offset architectures presented similar values of porosity at same strain and similar pore size, contrary to the 45° architecture. Thus, pore geometric configurations affected significantly the deformability of the all PCL scaffolds under compression. The prediction of the FEA showed a good agreement to the conventional mechanical tests revealing the areas more affected under compression load. The methodology proposed in this study using 3D printed scaffolds with compressionCT device and FEA is a framework that offers great potential in understanding the mechanical and structural behavior of soft systems for different applications, including for the biomedical engineering field.

No abstract

No abstract

<abstract> <p>Polydimethylsiloxane (PDMS) has been a promising material for microfluidic, particularly in lab-on-chip. Due to the panoply of good physical, mechanical and chemical properties, namely, viscosity, modulus of elasticity, colour, thermal conductivity, thermal coefficient of expansion, its application has been increasingly requested in quite different areas. Despite such characteristics, there are also some drawbacks associated, and to overcome them, several strategies have been developed to modify PDMS. Given the great variety of relevant conducted research in this field, the present work aims to gather the most relevant information, the advantages and disadvantages of some of the techniques used, and also identify potential gaps and challenges in it. To this end, a systematic literature review was conducted by collecting data from four different databases, Science Direct, American Chemical Society, Scopus, and Springer. Two authors independently screened the references, extracted the key information, and assessed the quality of the included studies. After the analysis of the collected data, 25 studies were selected that addressed the various mechanical properties of PDMS and how to modify them in order to suit a particular application.</p> </abstract>

In optogenetic studies, the brain is exposed to high-power light sources and inadequate power density or exposure time can cause cell damage from overheating (typically temperature increasing of 2 ∘C). In order to overcome overheating issues in optogenetics, this paper presents a neural tool capable of assessing tissue temperature over time, combined with the capability of electrical recording and optical stimulation. A silicon-based 8 mm long probe was manufactured to reach deep neural structures. The final proof-of-concept device comprises a double-sided function: on one side, an optrode with LED-based stimulation and platinum (Pt) recording points; and, on the opposite side, a Pt-based thin-film thermoresistance (RTD) for temperature assessing in the photostimulation site surroundings. Pt thin-films for tissue interface were chosen due to its biocompatibility and thermal linearity. A single-shaft probe is demonstrated for integration in a 3D probe array. A 3D probe array will reduce the distance between the thermal sensor and the heating source. Results show good recording and optical features, with average impedance magnitude of 371 kΩ, at 1 kHz, and optical power of 1.2 mW·mm−2 (at 470 nm), respectively. The manufactured RTD showed resolution of 0.2 ∘C at 37 ∘C (normal body temperature). Overall, the results show a device capable of meeting the requirements of a neural interface for recording/stimulating of neural activity and monitoring temperature profile of the photostimulation site surroundings, which suggests a promising tool for neuroscience research filed.