Compound semiconductors like gallium arsenide (GaAs) provide advantages over silicon for many applications, owing to their direct bandgaps and high electron mobilities. Examples range from efficient photovoltaic devices to radio-frequency electronics and most forms of optoelectronics. However, growing large, high quality wafers of these materials, and intimately integrating them on silicon or amorphous substrates (such as glass or plastic) is expensive, which restricts their use. Here we describe materials and fabrication concepts that address many of these challenges, through the use of films of GaAs or AlGaAs grown in thick, multilayer epitaxial assemblies, then separated from each other and distributed on foreign substrates by printing. This method yields large quantities of high quality semiconductor material capable of device integration in large area formats, in a manner that also allows the wafer to be reused for additional growths. We demonstrate some capabilities of this approach with three different applications: GaAs-based metal semiconductor field effect transistors and logic gates on plates of glass, near-infrared imaging devices on wafers of silicon, and photovoltaic modules on sheets of plastic. These results illustrate the implementation of compound semiconductors such as GaAs in applications whose cost structures, formats, area coverages or modes of use are incompatible with conventional growth or integration strategies.

We report the controlled growth of planar GaAs semiconductor nanowires on (100) GaAs substrates using atmospheric pressure metalorganic chemical vapor deposition with Au as catalyst. These nanowires with uniform diameters are self-aligned in <110> direction in the plane of (100). The dependence of planar nanowire morphology and growth rate as a function of growth temperature provides insights into the growth mechanism and identified an ideal growth window of 470 +/- 10 degrees C for the formation of such planar geometry. Transmission electron microscopy images reveal clear epitaxial relationship with the substrate along the nanowire axial direction, and the reduction of twinning defect density by about 3 orders of magnitude compared to <111> III-V semiconductor nanowires. In addition, using the concept of sacrificial layers and elevation of Au catalyst modulated by growth condition, we demonstrate for the first time a large area direct transfer process for nanowires formed by a bottom-up approach that can maintain both the position and alignment. The planar geometry and extremely low level of crystal imperfection along with the transferability could potentially lead to highly integrated III-V nanoelectronic and nanophotonic devices on silicon and flexible substrates.

Semiconductor nanowires have potential applications in photovoltaics, batteries, and thermoelectrics. We report a top-down fabrication method that involves the combination of superionic-solid-state-stamping (S4) patterning with metal-assisted-chemical-etching (MacEtch), to produce silicon nanowire arrays with defined geometry and optical properties in a manufacturable fashion. Strong light emission in the entire visible and near infrared wavelength range at room temperature, tunable by etching condition, attributed to surface features, and enhanced by silver surface plasmon, is demonstrated.

Semiconductor micro- and nanotubes can be formed by strain-induced self-rolling of membranes. The effect of geometrical dimensions on the self-rolling behavior of epitaxial mismatch-strained In(x)Ga(1-x)As-GaAs membranes are systematically studied both experimentally and theoretically using the finite element method. The final rolling direction depends on the length and width of the membrane as well as the diameter of the rolled-up tube. The energetics of the final states, the history of rolling process, and the kinetic control of the etching anisotropy ultimately determine the rolling behavior. Results reported here provide critical information for precise positioning and uniform large area assembly of semiconducting micro- and nanotubes for applications in photonics, microelectromechanical systems, etc.

No abstract

Spatial Light Interference Microscopy (SLIM) is a novel method developed in our laboratory that provides quantitative phase images of transparent structures with 0.3 nm spatial and 0.03 nm temporal accuracy owing to the white light illumination and its common path interferometric geometry. We exploit these features and demonstrate SLIM's ability to perform topography at a single atomic layer in graphene. Further, using a decoupling procedure that we developed for cylindrical structures, we extract the axially-averaged refractive index of semiconductor nanotubes and a neurite of a live hippocampal neuron in culture. We believe that this study will set the basis for novel high-throughput topography and refractometry of man-made and biological nanostructures.

A simple and efficient method for generating light emitting three-dimensional ͑3D͒ nanoscale pattern in silicon is presented. The method is based on differential chemical etching on and in-between patterned metal features. Effective transfer of various two-dimensional nanoscale ͑10-100 nm͒ metal patterns on bulk silicon to 3D porous silicon network is demonstrated. The capability and limitations of this method are discussed.

III-V microtubes and nanotubes are formed by a strain-induced self-rolling process. We report room-temperature photoluminescence (PL) characteristics of such microtubes with embedded GaAs quantum-well structures and wall thickness as thin as 38 nm. Rolled-up tubes show dramatic PL intensity enhancement compared to their planar counterparts. Holey tubes, formed using patterned membranes, display further increase in intensity implying better light extraction efficiency with the air holes. Systematic shift of PL peak position as a function of tube curvature, attributed to strain induced band structure change, is established.