Nanofluids, the fluid suspensions of nanomaterials, have shown many interesting properties, and the distinctive features offer unprecedented potential for many applications. This paper summarizes the recent progress on the study of nanofluids, such as the preparation methods, the evaluation methods for the stability of nanofluids, and the ways to enhance the stability for nanofluids, the stability mechanisms of nanofluids, and presents the broad range of current and future applications in various fields including energy and mechanical and biomedical fields. At last, the paper identifies the opportunities for future research.

A typical feature of polymer/fullerene based solar cells is that the current density under short-circuit conditions ͑J sc ͒ does not scale exactly linearly with light intensity ͑I͒. Instead, a power law relationship is found given by J sc ϰ I ␣ , where ␣ ranges from 0.85 to 1. In a number of reports this deviation from unity is speculated to arise from the occurrence of bimolecular recombination. We demonstrate that the dependence of the photocurrent in bulk heterojunction solar cells is governed by the build-up of space-charge in the device as a consequence of a difference in electron-and hole mobility. We have verified this for an experimental model system in which the mobility difference can be tuned from one to three orders of magnitude by changing the annealing treatment.

Various suspensions containing Al2O3 nanoparticles with specific surface areas in a range of 5–124 m2 g−1 have been prepared and their thermal conductivities have been investigated using a transient hot-wire method. Nanoparticle suspensions, containing a small amount of Al2O3, have substantially higher thermal conductivity than the base fluid, with the enhancement increasing with the volume fraction of Al2O3. The enhanced thermal conductivity increases with an increase in the difference between the pH value of aqueous suspension and the isoelectric point of Al2O3 particle. For the suspensions using the same base fluid, the thermal conductivity enhancements are highly dependent on specific surface area (SSA) of nanoparticle, with an optimal SSA for the highest thermal conductivity. For the suspensions containing the same nanoparticles, the enhanced thermal conductivity ratio is reduced with the increasing thermal conductivity of the base fluid. The crystalline phase of the nanoparticles appears to have no obvious effect on the thermal conductivity of the suspensions. Comparison between the experiments and the theoretical model shows that the measured thermal conductivity is much higher than the values calculated using theoretical correlation, indicating new heat transport mechanisms included in nanoparticle suspensions.

Although the thermal properties of millimeter-sized carbon nanotube mats and packed carbon nanofibers have been readily measured, measurements for a single nanotube are extremely difficult. Here, we report a novel method that can reliably measure the thermal conductivity of a single carbon nanotube using a suspended sample-attached T-type nanosensor. Our experimental results show that the thermal conductivity of a carbon nanotube at room temperature increases as its diameter decreases, and exceeds 2000 W/mK for a diameter of 9.8 nm. The temperature dependence of the thermal conductivity for a carbon nanotube with a diameter of 16.1 nm appears to have an asymptote near 320 K. The present method is, in principle, applicable to any kind of a single nanofiber, nanowire, and even single-walled carbon nanotube.

Multiwalled carbon nanotubes (CNTs) as produced are usually entangled and not ready to be dispersed into fluids. We treated CNTs by using a concentrated nitric acid to disentangle CNT aggregates for producing CNT nanofluids. Oxygen-containing functional groups have been introduced on the CNT surfaces and more hydrophilic surfaces have been formed during this treatment, which enabled to make stable and homogeneous CNT nanofluids. Treated CNTs were successfully dispersed into polar liquids like distilled water, ethylene glycol without the need of surfactant and into nonpolar fluid like decene with oleylamine as surfactant. We measured the thermal conductivities of these nanotube suspensions using a transient hot wire apparatus. Nanotube suspensions, containing a small amount of CNTs, have substantially higher thermal conductivities than the base fluids, with the enhancement increasing with the volume fraction of CNTs. For the suspensions with the same loading, the enhanced thermal conductivity ratios are reduced with the increasing thermal conductivity of the base fluid. Comparison between the experimental data and the theoretical model indicates that the thermal conductivities of nanotube suspensions seem to be very dependent on the interfacial layer that exists between the nanotube and the liquid.

There has been an explosion of research into the physical and chemical properties of carbon-based nanomaterials, since the discovery of carbon nanotubes (CNTs) by Iijima in 1991. Carbon nanomaterials offer unique advantages in several areas, like high surface-volume ratio, high electrical conductivity, chemical stability and strong mechanical strength, and are thus frequently being incorporated into sensing elements. Carbon nanomaterial-based sensors generally have higher sensitivities and a lower detection limit than conventional ones. In this review, a brief history of glucose biosensors is firstly presented. The carbon nanotube and grapheme-based biosensors, are introduced in Sections 3 and 4, respectively, which cover synthesis methods, up-to-date sensing approaches and nonenzymatic hybrid sensors. Finally, we briefly outline the current status and future direction for carbon nanomaterials to be used in the sensing area.

Electrochromic smart windows are regarded as a good choice for green buildings. However, conventional devices need external biases to operate, which causes additional energy consumption. Here we report a self-powered electrochromic window, which can be used as a self-rechargeable battery. We use aluminium to reduce Prussian blue (PB, blue in colour) to Prussian white (PW, colourless) in potassium chloride electrolyte, realizing a device capable of self-bleaching. Interestingly, the device can be self-recovered (gaining blue appearance again) by simply disconnecting the aluminium and PB electrodes, which is due to the spontaneous oxidation of PW to PB by the dissolved oxygen in aqueous solution. The self-operated bleaching and colouration suggest another important function of the device: a self-rechargeable transparent battery. Thus the PB/aluminium device we report here is bifunctional, that is, it is a self-powered electrochromic window as well as a self-rechargeable transparent battery.

No abstract