This study explores a quantitative evaluation of blood damage that occurs in a continuous flow left ventricular assist device due to fluid stress. Computational fluid dynamics (CFD) analysis is used to track the shear stress history of 388 particle streaklines. The accumulation of shear and exposure time is integrated along the streaklines to evaluate the levels of blood trauma. This analysis, which includes viscous and turbulent stresses, provides a statistical estimate of possible damage to cells flowing through the pump. In vitro normalized index of hemolysis values for clinically available ventricular assist devices were compared to our damage indices. This allowed for an order of magnitude comparison between our estimations and experimentally measured hemolysis levels, which resulted in a reasonable correlation. This work ultimately demonstrates that CFD is a convenient and effective approach to analyze the Lagranian behavior of blood in a heart assist device.

This study explores a quantitative evaluation of blood damage that occurs in a continuous flow left ventricular assist device (LVAD) due to fluid stress. Computational fluid dynamics (CFD) analysis is used to track the shear stress history of 388 particle streaklines. The accumulation of shear and exposure time is integrated along the streaklines to evaluate the levels of blood trauma. This analysis, which includes viscous and turbulent stresses, provides a statistical estimate of possible damage to cells flowing through the pump. Since experimental data for hemolysis levels in our LVAD are not available, in vitro normalized index of hemolysis values for clinically available ventricular assist devices were compared to our damage indices. This approach allowed for an order of magnitude comparison between our estimations and experimentally measured hemolysis levels, which resulted in a reasonable correlation. This work ultimately demonstrates that CFD is a convenient and effective approach to analyze the Lagrangian behavior of blood in a heart assist device.

A previously unpublished theory for describing the internal flow in a gas centrifuge is presented. The theory is based on boundary-layer-type arguments on the side walls of the centrifuge with the additional approximation of neglecting radial diffusion of radial momentum. The effects of the top and bottom end caps are incorporated through Ekman-layer solutions. The results are presented in a form amenable to numerical calculations.Some sample calculations are presented for the special case of a centrifuge with a linear temperature profile on the wall and the top and bottom of the centrifuge at the same temperature as the corresponding end of the side wall.

Mechanical circulatory support options for infants and children are very limited in the United States. Existing circulatory support systems have proven successful for short-term pediatric assist, but are not completely successful as a bridge-to-transplant or bridge-to-recovery. To address this substantial need for alternative pediatric mechanical assist, we are developing a novel, magnetically levitated, axial flow pediatric ventricular assist device (PVAD) intended for longer-term ventricular support. Three major numerical design and optimization phases have been completed. A prototype was built based on the latest numerical design (PVAD3) and hydraulically tested in a flow loop. The plastic PVAD prototype delivered 0.5-4 lpm, generating pressure rises of 50-115 mm Hg for operating speeds of 6,000-9,000 rpm. The experimental testing data and the numerical predictions correlated well. The error between these sets of data was found to be generally 7.8% with a maximum deviation of 24% at higher flow rates. The axial fluid forces for the numerical simulations ranged from 0.5 to 1 N and deviated from the experimental results by generally 8.5% with a maximum deviation of 12% at higher flow rates. These hydraulic results demonstrate the excellent performance of the PVAD3 and illustrate the achievement of the design objectives.

Thousands of cardiac failure patients per year in the United States could benefit from long-term mechanical circulatory support as destination therapy. To provide an improvement over currently available devices, we have designed a fully implantable axial-flow ventricular assist device with a magnetically levitated impeller (LEV-VAD). In contrast to currently available devices, the LEV-VAD has an unobstructed blood flow path and no secondary flow regions, generating substantially less retrograde and stagnant flow. The pump design included the extensive use of conventional pump design equations and computational fluid dynamics (CFD) modeling for predicting pressure-flow curves, hydraulic efficiencies, scalar fluid stress levels, exposure times to such stress, and axial fluid forces exerted on the impeller for the suspension design. Flow performance testing was completed on a plastic prototype of the LEV-VAD for comparison with the CFD predictions. Animal fit trials were completed to determine optimum pump location and cannulae configuration for future acute and long-term animal implantations, providing additional insight into the LEV-VAD configuration and implantability. Per the CFD results, the LEV-VAD produces 6 l/min and 100 mm Hg at a rotational speed of approximately 6300 rpm for steady flow conditions. The pressure-flow performance predictions demonstrated the VAD's ability to deliver adequate flow over physiologic pressures for reasonable rotational speeds with best efficiency points ranging from 25% to 30%. The CFD numerical estimations generally agree within 10% of the experimental measurements over the entire range of rotational speeds tested. Animal fit trials revealed that the LEV-VAD's size and configuration were adequate, requiring no alterations to cannulae configurations for future animal testing. These acceptable performance results for LEV-VAD design support proceeding with manufacturing of a prototype for extensive mock loop and initial acute animal testing.

A mock circulatory loop, which simulates the human circulatory system, is needed to bench test the various versions of continuous flow (CF) left ventricular assist devices (LVADs). This article describes the design and initial testing of such a loop. The loop consists of: (1) pulsatile left and right cardiac simulators; (2) air/water tanks to model the venous and arterial compliances; (3) tygon tubes to model the venous, arterial, and other system flow resistances; and (4) a tuning clamp to model the variation in system resistance characteristics under different cardiac pressure/flow conditions. Several loop measurements were carried out without an LVAD to verify the cardiovascular modeling of a healthy person in sleep, rest, and physical activity, and in different pathological states, and compared to the data found in the literature to validate the loop performance prior to LVAD testing.

A continuous flow left ventricle assist device (LVAD), which is mainly composed of a continuous flow blood pump and a physiological controller, has only one control input, the rotational speed of the pump, but at least three performance criteria to meet. The challenge for the physiological controller of a long-term continuous flow LVAD is the adaptability to different cardiovascular loading situations and the ability to handle systemic and parametric uncertainties with only one control input. The physiological LVAD controller presented in this article exhibits good performance in terms of the three performance criteria in different physiological loading conditions, such as disturbance, resting, and moderate exercise, for a patient with congestive heart failure. The collapse of the left ventricle, which is an inherent problem for a continuous flow LVAD, has been prevented because of the control algorithm design.

Vertical axis wind turbines have always been a controversial technology; claims regarding their benefits and drawbacks have been debated since the initial patent in 1931. Despite this contention, very little systematic vertical axis wind turbine research has been accomplished. Experimental assessments remain prohibitively expensive, while analytical analyses are limited by the complexity of the system. Numerical methods can address both concerns, but inadequate computing power hampered this field. Instead, approximating models were developed which provided some basis for study; but all these exhibited high error margins when compared with actual turbine performance data and were only useful in some operating regimes. Modern computers are capable of more accurate computational fluid dynamics analysis, but most research has focused on horizontal axis configurations or modeling of single blades rather than full geometries. In order to address this research gap, a systematic review of vertical axis wind-power turbine (VAWT) was undertaken, starting with establishment of a methodology for vertical axis wind turbine simulation that is presented in this paper. Replicating the experimental prototype, both 2D and 3D models of a three-bladed vertical axis wind turbine were generated. Full transient computational fluid dynamics (CFD) simulations using mesh deformation capability available in ansys-CFX were run from turbine start-up to operating speed and compared with the experimental data in order to validate the technique. A circular inner domain, containing the blades and the rotor, was allowed to undergo mesh deformation with a rotational velocity that varied with torque generated by the incoming wind. Results have demonstrated that a transient CFD simulation using a two-dimensional computational model can accurately predict vertical axis wind turbine operating speed within 12% error, with the caveat that intermediate turbine performance is not accurately captured.