A mechanochemical oxidation and cleavage reaction in lignin β-O-4 model compounds and lignin catalyzed by HO−TEMPO/ KBr/Oxone (TEMPO is 2,2,6,6-tetramethyl-1-piperidinyloxy) has been developed under milling conditions. The studies on nonphenolic lignin β-O-4 model compounds led to selective oxidations of the benzylic hydroxyl groups. Subjecting phenolic lignin model compounds to the oxidative conditions in a ball mill initiated aryl−C α bond cleavage reactions leading to the formation of the corresponding quinones and phenol derivatives. Transferring the mechanochemical protocol to lignin resulted in the simultaneous oxidation and cleavage of bonds with varied selectivity for monomeric products. Finally, a scale-up approach of the oxidative procedure by using vibrating disc mill technology enabled the mechanochemical protocol to be applied in gram-scale batch reactions under reduced milling time, while affording a similar extent of oxidation.

While the deposit qualities for mineral raw materials are constantly decreasing, the challenges for sustainable raw material processing are increasing. This applies not only to the demand for minimizing the consumption of energy, water, and reagents, but also to the reduction of residual materials, especially fine and difficult-to-landfill materials. Sensor‐based ore sorting can be used as a separation process for coarser grain sizes before the application of fine comminution and separation technologies and is applicable for a large variety of mineral raw materials. Sensor‐based ore sorting applies at various points in the process flow diagram and is suitable for waste elimination, for material diversion into different process lines, for the production of pre‐ and final concentrates, as well as for the reprocessing of coarse‐grained waste dumps and other applications. The article gives an overview of the development and state of the art of sensor‐based ore sorting for mineral raw materials and introduces various applications.

This work investigates the possible mineral input materials for the process of mineral sequestration through the carbonation of magnesium or calcium silicates under high pressure and high temperatures in an autoclave. The choice of input materials that are covered by this study represents more than 50% of the global peridotite production. Reaction products are amorphous silica and magnesite or calcite, respectively. Potential sources of magnesium silicate containing materials in Europe have been investigated in regards to their availability and capability for the process and their harmlessness concerning asbestos content. Therefore, characterization by X-ray fluorescence (XRF), X-ray diffraction (XRD), and QEMSCAN® was performed to gather information before the selection of specific material for the mineral sequestration. The objective of the following carbonation is the storage of a maximum amount of CO2 and the utilization of products as pozzolanic material or as fillers for the cement industry, which substantially contributes to anthropogenic CO2 emissions. The characterization of the potential mineral resources for mineral sequestration in Europe with a focus on the forsterite content led to a selection of specific input materials for the carbonation tests. The mineralogical analysis of an Italian olivine sample before and after the carbonation process states the reasons for the performed evaluation. The given data serves as an example of the input material suitability of all the collected mineral samples. Additionally, the possible conversion of natural asbestos occurring in minerals as a side effect of the carbonation process is taken into consideration.

Magnesium carbonate powders are essential in the manufacture of basic refractories capable of withstanding extremely high temperatures and for special types of cement and powders used in the paper, rubber, and pharmaceutical industries. A novel synthesis route is based on CO2 absorption/sequestration by minerals. This combines the global challenge of climate change with materials development. Carbon dioxide has the fourth highest composition in earth’s atmosphere next to nitrogen, oxygen and argon and plays a big role in global warming due to the greenhouse effect. Because of the significant increase of CO2 emissions, mineral carbonation is a promising process in which carbon oxide reacts with materials with high metal oxide composition to form chemically stable and insoluble metal carbonate. The formed carbonate has long-term stability and does not influence the earth’s atmosphere. Therefore, it is a feasible and safe method to bind carbon dioxide in carbonate compounds such as magnesite. The subject of this work is the carbonation of an olivine (Mg2SiO4) and synthetic magnesia sample (>97 wt% MgO) under high pressure and temperature in an autoclave. Early experiments have studied the influence of some additives such as sodium bicarbonate, oxalic acid and ascorbic acid, solid/liquid ratio, and particle size on the carbonation efficiency. The obtained results for carbonation of olivine have confirmed the formation of magnesium carbonate in the presence of additives and complete carbonation of the MgO sample in the absence of additives.

Silicon dioxide nanoparticles, also known as silica nanoparticles or nanosilica, are the basis for a great deal of biomedical and catalytic research due to their stability, low toxicity and ability to be functionalized with a range of molecules and polymers. A novel synthesis route is based on CO2 absorption/sequestration in an autoclave by forsterite (Mg2SiO4), which is part of the mineral group of olivines. Therefore, it is a feasible and safe method to bind carbon dioxide in carbonate compounds such as magnesite forming at the same time as the spherical particles of silica. Indifference to traditional methods of synthesis of nanosilica such as sol gel, ultrasonic spray pyrolysis method and hydrothermal synthesis using some acids and alkaline solutions, this synthesis method takes place in water solution at 175 °C and above 100 bar. Our first experiments have studied the influence of some additives such as sodium bicarbonate, oxalic acid and ascorbic acid, solid/liquid ratio and particle size on the carbonation efficiency, without any consideration of formed silica. This paper focuses on a carbonation mechanism for synthesis of nanosilica under high pressure and high temperature in an autoclave, its morphological characteristics and important parameters for silica precipitation such as pH-value and rotating speed.

Polymetallic nodules are a potential source of industrially demanded metals such as Ni, Co, Cu, and Mo (up to 3 wt %). Even if there is no deep-sea mining of manganese nodules today, a forecasted gap between metal demand and supply as well as continuously high metal prices may make seabed mining economically viable in the future. Up to now, a well-established industrial-scale extraction method for manganese nodules has been missing. Therefore, the aim of this study is to explore how economically interesting metals can be extracted from the nodules in a cost- and energy-efficient way. Polymetallic nodules have a heterogeneous chemical and structural composition without individual metal-rich particles. The economically interesting metals are distributed between different mineral phases (Mn-Fe-(oxy)hydroxides) as well as different growth structures that are intergrown with each other on a nm‒µm scale. Because of that a typical ore processing with the beneficiation of valuable particles is not feasible. The process presented here starts with a pyro-metallurgical pre-treatment of the polymetallic nodules, with the aim of creating artificial metal-rich (Ni, Cu, Co, Mo) particles with enrichment factors up to 10 compared to the original average metal contents. Afterwards, these particles should be beneficiated by conventional mineral processing steps to create a concentrate while reducing the mass stream in the process. The resulting metal particles can be further treated in conventional hydrometallurgical and/or pyro-metallurgical processes.

No abstract

Under mechanochemical conditions in ball mills, copper-and vanadium-containing minerals initiate atom transfer radical cyclizations and oxidative couplings, respectively. Only catalytic quantities of the minerals are required, and the reactions proceed either under neat conditions or in the presence of a minimal amount of solvent.