Biyomedikal malzeme endüstrisi, insanların hayat kalitesini ve buna bağlı aktivitelerini sürdürebilmeleri amacıyla dünya çapında gelişmeye devam etmektedir. Yaşlı nüfus ve refah seviyesinin artış göstermesi biyomedikal malzeme sektörünün hızlı bir şekilde büyümesini sağlayan başlıca sebepler arasındadır. Vücut içerisinde implantasyonun yapılacağı bölgenin özelliklerine göre tercih edilen malzeme grubu değişmektedir. Bu malzemeler arasında metalik biyomalzemeler üstün mekanik özelliklerinden dolayı yüksek kullanım oranına sahiptir. Polimer esaslı, seramik esaslı ve kompozit biyomalzemelerde olduğu gibi metalik biyomalzemelerin de konak canlıda oluşturduğu problemler birçok etkene bağlıdır. Oluşan sorunlara karşı yapılan çalışmalar ve gelişen teknoloji ile birlikte günümüzde yenilikçi çözümler üretilmektedir. Metalik biyomalzemeler sahip oldukları yüksek elastisite modülü ile biyomekanik uyumsuzluğa sebep olurken, içerdikleri alaşım element iyonlarının toksik etki oluşturması sonucunda biyouyumluluğu tehlikeye atmaktadırlar. Bundan dolayı derleme doğrultusunda temelde yaşanan iki probleme karşı geliştirilen, biyouyumluluğu yüksek elementlerle alaşımlanan ve faz yapısı sayesinde düşük elastisite modülüne sahip olan β tipi Ti alaşımlarının özellikleri incelenmiştir. Bununla birlikte, β tipi Ti alaşımlarının üretim yöntemlerinin alaşım üzerindeki etkileri üzerinde durulmuş bu noktada toz metalürjisi teknolojisi ile geliştirilen alaşımların verimliliği araştırılmıştır.
Bearing materials are used in many industrial applications such as automotive, marine, aviation and hydroelectric power plants. Powder metallurgy is preferred because it is economically more advantageous in the production of this type of material. The main requirement in bearing materials is high tribological properties at a low cost. Therefore, the lower coefficient of friction and wear rate in the bearing materials are among the desired properties. In this regard, the tribological properties and other mechanical, physical, and microstructural properties of the produced samples were investigated in this study. Copper and graphite powder with 5 wt.% Mo, Ni, Al, Cr, and W was added to the base alloy of iron. After the production, density measurements, microstructural characterizations, hardness measurements, and dry friction wear tests were carried out on the samples. Analyzing the results, it was found that the highest density value was achieved in the base alloy. Furthermore, a density of over 90% was achieved in all samples. On the other hand, predominantly ferrite and pearlite phases were observed in the microstructure. When the hardness results were examined, it was determined that the Cr added alloys had maximum hardness. In the evaluation of tribological properties, it was shown that Ni alloy had the lowest friction coefficient and Al alloy had the highest friction coefficient. Considering the wear rates, it was seen that the alloy with the lowest wear rate was Cr and the highest wear rate was the alloy with Al additives.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.