The measurement of machined-part strain fields induced by the cutting process remains a challenge because of the presence of highly intensive and localised strains. In this study, a high-speed double-frame imaging device with pulsed laser lighting is used in order to obtain sharp and highly resolved images during orthogonal cutting tests performed in an aluminium alloy. The displacement fields are then measured using a global Q4-digital-image-correlation (DIC) method and several strategies, facilitating calculation of the total displacements due to the cut, along with the residual strains in the machined part. Numerical procedures are developed to manage the removed material that disturbs the DIC. An automatic primary shear angle detection procedure using DIC is also proposed. Five different markings, which are produced via chemical etching and micro blasting, are applied to the observed surfaces. Their effects on the kinematic fields and the uncertainties are then studied. Three surface parameters are proposed as indicators for determining the surface preparation suitability for the DIC. The repeatability of the kinematic fields induced during the cutting process is studied, because of the ease with which testing can be performed. Finally, the plastically deformed layer engendered by the cutting process is measured using the calculated residual strains.

is an open access repository that collects the work of Arts et Métiers ParisTech researchers and makes it freely available over the web where possible. AbstractThe quantification of friction coefficient along the tool-workmaterial interface in machining remains an issue in tribology. This paper aims identifying the evolution of friction coefficient for a large range of sliding velocity during the machining of a AISI4140 steel (290 HB) with a TiN coated carbide tool. The influence of a straight oil is investigated compared to a dry sliding situation (dry machining). It has been shown that, in dry machining, friction coefficient decreases with the sliding velocity until reaching a downer limit around 0.2. On the contrary, the presence of a straight oil decreases significantly friction coefficients to a value around 0.1. Additionally, the friction coefficient becomes independent from the sliding velocity. It also been shown that a straight oil is able to penetrate the pin-workmaterial interface even if a very high contact pressure is present (~3 GPa). The penetration duration is very fast, whereas its evacuation duration is much higher and strongly dependant on sliding speeds.

is an open access repository that collects the work of Arts et Métiers ParisTech researchers and makes it freely available over the web where possible.This is an author-deposited version published in: https://sam.ensam.eu Handle ID: .http://hdl.handle.net/10985/7466 To cite this version :Guillaume FROMENTIN, Gérard POULACHON -Modeling of interferences during thread milling operation -The International Journal of Advanced Manufacturing Technology -Vol. 49, n°1, p.41-51 -2010 Any correspondence concerning this service should be sent to the repository Administrator : archiveouverte@ensam. eu 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 Modeling of interferences during thread milling operation Abstract: Thread milling is becoming more and more employed as a technique for producing thread, due to its advantages for industrial manufacturing sectors, such as the aeronautics, aerospace, and energy industries. The thread milling operation is atypical and several aspects have to be taken into account to perform it in good conditions. As for milling or grinding worms, grooves, thread or others sculptured surfaces, in thread milling, there exists a geometrical interference between the tool and the nominal surface which would be obtained. Thread mills have quite complex geometry and their profile has an effect on the machined thread. The present study details geometrical aspects of the thread milling process. This article deals with the link between thread mill geometry and nominal thread profile. An approach is proposed to analyze the thread profile generated by the thread mill envelope. It is deduced that thread milling produces interferences, i.e. the machined thread profile is affected by an overcut. A method is proposed to correct this geometrical error in order to produce accurate thread. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 D mgt : maximum diameter of the generated thread E r : radial error between nominal and generated thread 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64

Machining accuracy can be compromised by elastic workpiece deformation and subsurface residual stress introduction during cutting. In order to anticipate the impact of cutting forces and surface integrity evolutions on finished surface and its geometrical errors, it is necessary to better understand the influence of cutting conditions and tool wear. In this study, machinability of Inconel 718 using a round carbide tool in finish turning conditions is assessed. Cutting forces evolution during tool life are analysed and accompanied by advanced investigations of cutting phenomena. An original mechanistic cutting force model is developed, identified and tested. It includes the effect of tool wear over time in its local formulation. This model allows predicting cutting forces evolution along tool pass for a wide range of finishing cutting conditions. Furthermore, a thorough analysis of residual stress profiles at different tool wear levels is led. It features quantitative results for fresh and worn tools. A study on the influence of cutting parameters and tool wear on residual stress profiles in the machining affected zone is highlighted.

Largely applied to internal threading of extruded tubes, cold form tapping is now becoming a promising process for internal threading of holes in non ferrous and ferrous solid components, more particularly for mass production in the automotive industry. The aim of this study is to present the surface properties of the threads resulting from form tapping. Geometrical characterization, surface texture, mechanical and metallurgical observations are investigated. The results obtained are discussed according to the input parameters of the process, and are compared to those obtained from cut tapping. The strength of the work material and the influence of the lubricant are the two main parameters affecting the process, and a correlation with the tapping torque is proposed. Finally, the characteristics of the thread surface depend on the parameters of the tapping operation, thus it has to be taken into account in the design approach when this tapping process is chosen.

No abstract

is an open access repository that collects the work of Arts et Métiers ParisTech researchers and makes it freely available over the web where possible.

is an open access repository that collects the work of Arts et Métiers ParisTech researchers and makes it freely available over the web where possible.This is an author-deposited version published in: http://sam.ensam.eu Handle ID: .http://hdl.handle.net/10985/7470 To cite this version :Guillaume FROMENTIN, Gérard POULACHON -Geometrical analysis of thread milling -Part 1: Evaluation of tool angles -The International Journal of Advanced Manufacturing TechnologyVol. 49, n°1, p.73-80 -2010 Any correspondence concerning this service should be sent to the repository Administrator : archiveouverte@ensam. eu 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 Keywords: thread milling, cutting geometry, tool angles Abstract: Thread milling is a method which is increasingly used for machining thread. For this operation, a helical interpolation is required. Furthermore, the thread mill is a tool whose geometry is rather complex. Its envelope profile is linked to the thread profile and a single tooth of the thread mill is composed of three continuous cutting edges. The present study proposes a geometrical model and an analytical formulation to define the rake face and the cutting edge. Further, the calculations of cutting planes and cutting angles are explained. The analysis shows specific aspects of thread mills, in particular the fact that the flute angle may lead to a negative rake angle. This study is a contribution to cutting geometry aspect and constitutes a step for cutting force model in thread milling.