Abstract. Simulations of the dust cycle and its interactions with the changing Earth system are hindered by the empirical nature of dust emission parameterizations in weather and climate models. Here we take a step towards improving dust cycle simulations by using a combination of theory and numerical simulations to derive a physically based dust emission parameterization. Our parameterization is straightforward to implement into large-scale models, as it depends only on the wind friction velocity and the soil's threshold friction velocity. Moreover, it accounts for two processes missing from most existing parameterizations: a soil's increased ability to produce dust under saltation bombardment as it becomes more erodible, and the increased scaling of the dust flux with wind speed as a soil becomes less erodible. Our treatment of both these processes is supported by a compilation of quality-controlled vertical dust flux measurements. Furthermore, our scheme reproduces this measurement compilation with substantially less error than the existing dust flux parameterizations we were able to compare against. A critical insight from both our theory and the measurement compilation is that dust fluxes are substantially more sensitive to the soil's threshold friction velocity than most current schemes account for.

No abstract

Abstract.A comparison of two popular eddy-covariance software packages is presented, namely, EddyPro and TK3. Two approximately 1-month long test data sets were processed, representing typical instrumental setups (i.e., CSAT3/LI-7500 above grassland and Solent R3/LI-6262 above a forest). The resulting fluxes and quality flags were compared. Achieving a satisfying agreement and understanding residual discrepancies required several iterations and interventions of different nature, spanning from simple software reconfiguration to actual code manipulations. In this paper, we document our comparison exercise and show that the two software packages can provide utterly satisfying agreement when properly configured. Our main aim, however, is to stress the complexity of performing a rigorous comparison of eddy-covariance software. We show that discriminating actual discrepancies in the results from inconsistencies in the software configuration requires deep knowledge of both software packages and of the eddy-covariance method. In some instances, it may be even beyond the possibility of the investigator who does not have access to and full knowledge of the source code. Being the developers of EddyPro and TK3, we could discuss the comparison at all levels of details and this proved necessary to achieve a full understanding. As a result, we suggest that researchers are more likely to get comparable results when using EddyPro (v5.1.1) and TK3 (v3.11) -at least with the setting presented in this paper -than they are when using any other pair of EC software which did not undergo a similar cross-validation.As a further consequence, we also suggest that, to the aim of assuring consistency and comparability of centralized flux databases, and for a confident use of eddy fluxes in synthesis studies on the regional, continental and global scale, researchers only rely on software that have been extensively validated in documented intercomparisons.

Eddy covariance flux research has relied on open-or closed-path gas analyzers for producing estimates of net ecosystem exchange of carbon dioxide (CO 2 ) and water vapor (H 2 O). The two instruments have had different challenges that have led to development of an enclosed design that is intended to maximize strengths and minimize weaknesses of both traditional designs. Similar to the closed-path analyzer, the enclosed design leads to minimal data loss during precipitation events and icing, and it does not have surface heating issues. Similar to the open-path design, the enclosed design has good frequency response due to small flux attenuation loss in the short intake tube, does not need frequent calibration, has minimal maintenance requirements, and can be used in a very low power configuration. Another important feature of such a design is the ability to output instantaneous mixing ratio, or dry mole fraction, so that instantaneous thermal and pressure-related expansion and contraction, and water dilution of the sampled air have been accounted for. Thus, no density corrections should be required to compute fluxes during postprocessing. Calculations of CO 2 and H 2 O fluxes via instantaneous mixing ratio from the new enclosed CO 2 /H 2 O gas analyzer were tested in nine field experiments during 2009-2010 in a wide range of ecosystems and setups. Fluxes computed via a mixing ratio output from the instrument without applying density corrections were compared to those computed the traditional way using density corrections. The results suggest that with proper temperature, water vapor, and pressure measurements in the cell, gas fluxes can be computed confidently from raw covariance of mixing ratio and vertical wind speed, multiplied by a frequency response correction. This has important implications for future flux measurements, because avoiding hourly density corrections could have the advantages of increasing flux measurement quality and temporal resolution, reducing the magnitude of minimum detectable flux, unifying data processing steps, and assuring better intercomparison between different sites and networks.