The tungsten (W) material in the high heat flux regions of the ITER divertor will be exposed to high fluxes of low-energy particles (e.g. H, D, T, He, Ne and/or N). Combined with long-pulse operations, this implies fluences well in excess of the highest values reached in today's tokamak experiments. Shaping of the individual monoblock top surface and tilting of the vertical targets for leading-edge protection lead to an increased surface heat flux, and thus increased surface temperature and a reduced margin to remain below the temperature at which recrystallization and grain growth begin. Significant morphology changes are known to occur on W after exposure to high fluences of low-energy particles, be it H or He. An analysis of the formation conditions of these morphology changes is made in relation to the conditions expected at the vertical targets during different phases of operations. It is concluded that both H and He-related effects can occur in ITER. In particular, the case of He-induced nanostructure (also known as 'fuzz') is reviewed. Fuzz formation appears possible over a limited region of the outer vertical target, the inner target being generally a net Be deposition area. A simple analysis of the fuzz growth rate including the effect of edge-localized modes (ELMs) and the reduced thermal conductivity of fuzz shows that the fuzz thickness is likely to be limited by the occurrence of annealing during ELM-induced thermal excursions. Not only the morphology, but the material mechanical and thermal properties can be modified by plasma exposure. A review of the existing literature is made, but the existing data are insufficient to conclude quantitatively on the importance and extent of these effects for ITER. As a consequence of the high surface temperatures in ITER, W recrystallization is an important effect to consider, since it leads to a decrease in material strength. An approach is proposed here to develop an operational budget for the W material, i.e. the time the divertor material can be operated at a given temperature before a significant fraction of the material is recrystallized. In general, while it is clear that significant surface damage can occur during ITER operations, the tolerable level of damage in terms of plasma operations currently remains unknown.

TCV experiments demonstrate the basic power exhaust properties of the snowflake (SF) plus and SF minus divertor configurations by measuring the heat fluxes at each of their four divertor legs. The measurements indicate an enhanced transport into the private flux region and a reduction of peak heat fluxes compared to a similar single null configuration. There are indications that this enhanced transport cannot be explained by the modified field line geometry alone and likely requires an additional or enhanced cross-field transport channel. The measurements, however, do not show a broadening of the scrape-off layer (SOL) and, hence, no increased cross-field transport in the common flux region. The observations are consistent with the spatial limitation of several characteristic SF properties, such as a low poloidal magnetic field in the divertor region and a long connection length to the inner part of the SOL closest to the separatrix. Although this limitation is typical in a medium sized tokamak like TCV, it does not apply to significantly larger devices where the SF properties are enhanced across the entire expected extent of the SOL.

One of the main challenges in developing highly efficient nanostructured photoelectrodes is to achieve good control over the desired morphology and good electrical conductivity. We present an efficient plasma-processing technique to form porous structures in tungsten substrates. After an optimized two-step annealling procedure, the mesoporous tungsten transforms into photoactive monoclinic WO3. The excellent control over the feature size and good contact between the crystallites obtained with the plasma technique offers an exciting new synthesis route for nanostructured materials for use in processes such as solar water splitting.

This work discusses the response of ultrafine-grained tungsten materials to high-flux, high-fluence, low energy pure He irradiation. Ultrafine-grained tungsten samples were exposed in the Pilot-PSI (Westerhout et al 2007 Phys. Scr. T128 18) linear plasma device at the Dutch Institute for Fundamental Energy Research (DIFFER) in Nieuwegein, the Netherlands. The He flux on the tungsten samples ranged from 1.0 × 1023–2.0 × 1024 ions m−2 s−1, the sample bias ranged from a negative (20–65) V, and the sample temperatures ranged from 600–1500 °C. SEM analysis of the exposed samples clearly shows that ultrafine-grained tungsten materials have a greater fluence threshold to the formation of fuzz by an order or magnitude or more, supporting the conjecture that grain boundaries play a major role in the mechanisms of radiation damage. Pre-fuzz damage analysis is addressed, as in the role of grain orientation on structure formation. Grains of (1 1 0) and (1 1 1) orientation showed only pore formation, while (0 0 1) oriented grains showed ripples (higher structures) decorated with pores. Blistering at the grain boundaries is also observed in this case. In situ TEM analysis during irradiation revealed facetted bubble formation at the grain boundaries likely responsible for blistering at this location. The results could have significant implications for future plasma-burning fusion devices given the He-induced damage could lead to macroscopic dust emission into the fusion plasma.

Ammonia synthesis from hydrogen and nitrogen gases by low-temperature radio frequency plasma catalysis.

No abstract

The first combined experimental and theoretical studies of dust remobilization by plasma forces are reported. The main theoretical aspects of remobilization in fusion devices under steady state conditions are analyzed. In particular, the dominant role of adhesive forces is highlighted and generic remobilization conditions -direct lift-up, sliding, rolling -are formulated. A novel experimental technique is proposed, based on controlled adhesion of dust grains on tungsten samples combined with detailed mapping of the dust deposition profile prior and post plasma exposure. Proof-ofprinciple experiments in the TEXTOR tokamak and the EXTRAP-T2R reversed-field pinch are presented. The versatile environment of the linear device Pilot-PSI allowed for experiments with different magnetic field topologies and varying plasma conditions that were complemented with camera observations.

The thermal response of nanostructured tungsten, which was fabricated in the linear divertor simulator NAGDIS-II, was investigated using pulsed plasma in the MAGNUM-PSI device and by using high powered laser pulses. The temperature evolution in response to the pulses was measured with an infrared fast framing camera. The temperature increase in response to the pulses on the nanostructured sample was significantly greater than that of the pristine sample both for plasma and laser pulses. After the pulsed plasma/laser irradiation, the nanostructured surface was observed to have melted although the measured surface temperature was much less than the melting temperature. The mechanism to account for the difference in the temporal evolution of temperature between the nanostructured and pristine samples is discussed. It is suggested that there are thermally isolated part on the nanostructures and anomalous temperature increase and melting have occurred locally on them. The amount of vapourized tungsten in response to type-I edge localized mode in ITER is discussed based on experimental observation.