The promotion of electric energy production from solid biomass by the Austrian government has lead to a boom in the construction of new combined heat and power plants. The current total demand for wood chips in the research area for energy purposes is 70 400 m 3 of loose volume chips per year. The expected increase in demand due to these new plants is more than 4 times greater than current demand: up to 302 700 m 3 of loose volume per year. Even if the energy wood feedstock potential is satisfactory, the design of the supply chain is still unresolved. The aim of this study is to give decision-makers a base for further development. To accomplish this, we designed and tested four different supply scenarios: one for 9 plants and one for 16 plants. The scenarios were developed using a combination of geographic information systems (GIS) and linear programming methods. The results indicate that direct transport of solid fuel wood as round wood and chipping at the plant is the cheapest supply system with a resulting cost of 5.6-6.6 EUR/m 3 loose. Using harvesting residues can only be recommended for large plants because of poor fuel quality. In this case, residues would be chipped at or near the landing, piled and transported via self-loading trucks at a cost between 8.4 and 9.1 EUR/m 3 loose. In order to meet increasing demand and to ensure a continuous supply, especially during the winter and spring seasons it is necessary to optimize the supply chain by including storage terminals. However, using terminals and increased demand both lead to higher logistical costs. For example, if the total volume is handled via terminals, the average supply costs including storage will increase by 26%. Higher demand increases the costs by 24%.
Round wood supply in Austria is often affected by different factors such as bottlenecks or oversupply due to changing market, weather and road conditions. An additional factor impacting the complex wood supply chain is the rising transport costs from the landing to the sawmill. Logging trucks are the primary transportation technology used from the forest to the customer's site. The objectives of this study were to analyze the actual situation and characteristics of typical trucking activities for round wood supply from the region to an Austrian sawmill. The study used time and fuel consumption, proportion of travel on forest roads and average speed on different functional road classes to estimate productivity and costs. Data collection including GPS-tracking was done using fleet management equipment built into the driver's cabin. The GPS-routes were analyzed in ArcGIS 9.3 based on the national road network and its attributes. The sawmill studied with a yearly demand of 600,000 m 3 round wood was located in southern Austria. In total, more than 2,000 round trips operated by seven logging trucks recorded close to 100,000 km. The transport distance from the forest to the sawmill averaged 51 km. The average share on forest roads within a route to the sawmill was 14.2% with an average speed of 13.5 km/h, whereby the forest road is defined as road with minor importance. Transport costs from the forest site to the sawmill with a truck and trailer were € 11/m 3 solid timber based on an average load size of 25 m 3 . An average 0.77 l of diesel fuel per kilometer was consumed during a round trip including all work phases. A trip to an interim storage location consumed 2.05 l/km due to the number of work phases without driving distance.
Effect of multi-tree handling and tree-size on harvester performance in small-diameter hardwood thinnings Erber G., Holzleitner F., Kastner M., Stampfer K. (2016). Effect of multi-tree handling and tree-size on harvester performance in small-diameter hardwood thinnings. Silva Fennica vol. 50 no. 1 article id 1428. 17p. Highlights• Harvesting with the accumulating energy wood head EF28 was studied under small tree dimension (8 dm³) in hardwood thinnings.• Reasonable productivity was achieved.• Maximum achieved cutting diameter in hornbeam stand was 23 cm and 15% lower than in softwood stands.• Head has potential under such conditions. AbstractEarly thinnings are laborious and costly. Thus forest companies are searching for cost and time efficient ways to carry out this task. The study's purpose was to determine the productivity of the EF28 accumulating energy wood harvesting head in harvesting small-diameter hornbeam (Carpinus betulus L.) undergrowth trees and evaluate the effect of its multi-tree handling (MTH) capacity on time consumption. The harvester was a wheeled, three-axle Komatsu 911. A time study of 7.1 hours on 19 plots, with a total area of 0.76 ha was conducted. On average, the harvested tree volume was 8 dm³ and the stand density was 2666 trees/ha. The productivity was modelled with MTH conduction, mean diameter at breast height and the number of trees handled per cycle as independent variables. On average, MTH took 27% longer per cycle, increased extracted volume per cycle by 33% and consequently increased productivity with 5.0%. In 71.9% of the cycles more than one tree was handled and if so, dimensions were smaller than in single-tree handling (5.8 cm vs. 12.0 cm). Maximum felling diameter of 23 cm was about 15% smaller than in softwood (according to the manufacturer's specifications) and the driver didn't exploit the EF28's theoretical potential in terms of trees handled per cycle. It can be concluded that the head could significantly improve productivity in small-diameter wood procurement.
Purpose of Review Winch-assist systems have seen rapid development, adoption, and implementation in many parts of the world in the past decade and can be considered one of the major recent innovations in steep terrain harvesting. Though a comparatively young topic, the literature around this topic has grown considerably during the last decade. This review summarizes the present body of literature on winch-assist systems and provides a comprehensive introduction to the topic. Recent Findings The analysis showed that work safety in steep terrain harvesting operations has increased through winch-assist systems by removing workers from the many hazards of manual and motor-manual work. The extent of rutting, subsequent erosion, and soil densification after working with winch-assist systems was found to be similar to operations on gentle terrain or cable logging. Winch-assist harvesting is considered more productive than conventional steep terrain harvesting. While case studies provide indicative utilization and productivity values, a robust understanding of economic viability under varied stand and terrain conditions is not yet well established. Summary Winch-assist is proving to be a robust, safe, and high-performance forest harvesting technology that has increased the operating range of ground-based, mechanized harvesting. It can help increase access to forest grounds in steep terrain that are previously considered economically marginal for forest management. Besides steep terrain, the potential benefits of winch-assist in reducing soil disturbance from ground-based equipment indicate that its operating range can also expand to gentle terrain where environmental impacts are of great concern due to wet or unstable soils. As the technology is relatively young and still evolving, there are many unknown social, environmental, and economic challenges and opportunities associated with the winch-assist technology. More research is certainly warranted.
Controlling and organizing the complex forest-to-consumer supply chain of wood fuels is a challenging task, especially for the chipping and transport processes. Truck mounted chippers and transport trailer-trucks must be scheduled to minimize delay to be profitable. Job management within the supply chain, including machine activity based controlling, offers a new way to increase efficiency and productivity. However, detailed data are required to detect and analyze potential gaps and improve forest fuel supply. Generally, data regarding the wood fuel supply chain process are obtained from extensive time studies that are based on a specific process step. Although time studies can detect details during the production of forest fuels, they only describe certain time frames. Long-term data that are recorded during the entire year could encompass seasonal and short term effects. This study aims to monitor the forest fuel supply processes (semi-automated), specifically regarding time and fuel consumption. Large data sets were automatically and efficiently gathered with little effort by drivers and operators. Data were recorded with fleet management equipment for more than 14 months. Vehicle data, including GPS data, were logged at an interval of one minute. Data management was conducted in a pre-configured database that contained pre-defined reports and were run by the Institute of Forest Engineering, Vienna. Work step assignments were implemented with Structured Query Language (SQL)-routines by using the raw machine activities data and GPS. The chipping and transport activities of more than 240 loads were analyzed by focusing on fuel consumption, time needed and traffic. The average distance between chipping sites and plants was approximately 54 kilometers. Fuel consumption from transport reached 50 l/100 km. The chipping unit reached a productivity of 12.8 odt/PSH15 and had a fuel consumption of 58 liters per operating hour.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.