No abstract

Increasing concerns about the depletion of fossil resources and the issue of environment lead to a global need for producing more clean energy from renewable sources. Ocean is appreciated as a vast source of renewable energies. Considering marine renewable energies, it can be noticed that significant electrical power can be extracted from marine tidal currents. However, the power harnessed from marine tidal currents is highly fluctuant due to the swell effect and the periodicity of the tidal phenomenon. To improve the power quality and make the marine generation system more reliable, energy storage systems can play a crucial role. In this paper, an overview and the state of art of energy storage technologies are presented. Characteristics of various energy storage technologies are analyzed and compared for this particular application. The comparison shows that high-energy batteries like sodium-sulphur battery and flow battery are favorable for smoothing the long-period power fluctuation due to the tide phenomenon while supercapacitor and flywheel are more suitable for eliminating short-period power disturbances due to swell or turbulence phenomena.This means that hybrid storage technologies are needed for achieving optimal results in tidal marine current energy applications.

is an open access repository that collects the work of Arts et Métiers ParisTech researchers and makes it freely available over the web where possible.This is an author-deposited version published in: http://sam.ensam.eu Handle ID: .http://hdl.handle.net/10985/6957 To cite this version :Franck SCUILLER, Eric SEMAIL, Jean-Frederic CHARPENTIER, Paul LETELLIER -Multi-criteria based design approach of multiphase permanent magnet low speed synchronous machinesElectric Power Applications, IET -Vol. 3, n°2, p.102-110 -2009 Any correspondence concerning this service should be sent to the repository portunities for increasing torque density using the harmonics are considered. The specific constraints due to the PWM supply of multiphase machines are also taken into account during the design phase. All the defined constraints are expressed in a simple manner by using a multimachine modelling of the multiphase machines. This multimachine design is then applied in order to meet the specifications of a marine propeller: verifying simultaneously four design constraints, an initial 60-pole 3-phase machine is converted into a 58-pole 5-phase machine without changing the geometry and the active volume (iron, copper and magnet). Firstly, a specific fractional-slot winding, which yields to good characteristics for PWM supply and winding factors, is chosen. Then, using this winding, the magnet layer is designed to improve the flux focussing. According to analytical and numerical calculations, the five-phase machine provides a higher torque (about 15%) and less pulsating torque (71% lower) than the initial three-phase machine with the same copper losses.

is an open access repository that collects the work of Arts et Métiers ParisTech researchers and makes it freely available over the web where possible. Abstract-Five-phase Surface-Mounted Permanent Magnet (SMPM) machines can inherently produce a smooth electromagnetic torque which can be increased when using third harmonic current injection. To really take advantage of these characteristics, the rotor magnets can be shaped in order to obtain a back-emf with large third harmonic term. This is the scope of the paper. For the design specifications of a low speed marine propulsion machine, the following objective must be achieved: to significantly mitigate the pulsating torque without reducing the average torque bearing in mind the solution where the rotor is made with full pole-pitch magnets. An analytical field computation, called equivalent coil method, is developed in order to quicly explore the magnet geometries. Thus a procedure to optimize small trapezoid notches at the surface of the pole magnets is performed. Referring to the classical fully pole-pitch magnet shape, the solution found allows a substantial reduction of the pulsating torque without reducing the torque density. Furthermore, with regard to an equivalent three-phase machine, for the same copper losses, the average torque of the optimized five-phase machine can be potentially higher if the third harmonic current injection is implemented.

Abstract-This paper deals with the rough design of a Double-Stator Axial Flux Permanent Magnet Machine (DSAFPM) for a rim-driven Marine Current Turbine (MCT). The DSAFPM machine will be compared to a previously developed and realized Radial Flux Permanent Magnet Machine (RFPM); given the same rim-driven MCT specifications. For that purpose, a first-order electromagnetic design model and a thermal one are developed and used to compare active part mass, cost, and thermal behavior of the two machines.The obtained results show that such a structure of poly-air gap axial flux machine can be more interesting in terms of compactness and thermal behavior for rim-driven marine current turbines.Index Terms-Marine current turbine, rim-driven concept, permanent magnet machine, axial flux machine, electromagnetic model, thermal model.

is an open access repository that collects the work of Arts et Métiers ParisTech researchers and makes it freely available over the web where possible. Abstract-This

In this paper, the study of the torque and power versus speed characteristics for a family of five-phase Surfacemounted Permanent Magnet (SPM) machine is carried out. With considering hypotheses (linear magnetic modeling, only first and third harmonic terms in the back-emf and current spectrums), an optimization problem that aims to maximize the torque for given maximum peak voltage and RMS current is formulated: the optimal torque sharing among the two virtual machines (the two dq-axis subspaces) that represent the real five-phase machine is thus calculated for any mechanical speed. For an inverter and a DC voltage sized with only considering the first harmonic of backemf and current, the problem is solved with changing the virtual machine back-emfs and inductances ratios. With the introduction of the maximum torque/speed point, maximum power/speed point and maximum reachable speed, it can be shown that, if the inductance ratio is large enough, for given Volt-Ampere rating, the machine can produce higher torque without reducing its speed range thus meaning that the capability of the inverter to work is improved with the use of the third harmonic. This property is all the truer as the base armature reaction is large. A particular five-phase machine is sized and numerically analyzed to check this property.

is an open access repository that collects the work of Arts et Métiers ParisTech researchers and makes it freely available over the web where possible. Abstract-In this paper, an original multi-phase Surface Mounted Permanent Magnet (SMPM) Machine designed for naval propulsion is proposed. The design objective of this high power low speed machine is twofold: to enhance the fault tolerance capability of the system and to optimize the quality of the torque by reducing the electromagnetic torque ripples which underlie the acoustic behaviour of the motor and of the global mechanical structure. A low level of ripple torques must also be ensured in faulty operations. To fullfill these constraints, the machine is equipped with a fractional-slot concentrated winding made up of four 3-phase windings each one being star-connected, each star being magnetically shifted by an angle of 15 degrees. This 4-star 3-phase configuration allows to reduce the cogging torque and to separate magnetically and physically the phase windings. The end-turns are also drastically reduced, which improves the compactness and the efficiency of the machine. This original multi-phase machine is supplied by four 3-phase PWM voltage source inverter with sinusoidal current law. The magnetic independences between the four star windings allow a very simple control of the four-star supply and a straightforward fault operating mode. Moreover, this 4-star winding configuration yields to very low torque ripples in nominal configuration (four stars connected) and in faulty operations if two magnetic non adjacent stars are disconnected. For all these reasons, this structure appears particularly suitable for naval propulsion application since it increases the machine performances in terms of compactness, reliability and quality of torque.