ObjectivesThe aim of this study was to determine the fluoride levels in breast milk and plasma of lactating mothers who regularly consumed drinking water with low levels of fluoride.MethodsOne hundred twenty five healthy mothers aged between 20–30 years old who had given birth within 5–7 days were included in the study. Besides being otherwise healthy, the primary selection criteria stipulated the absence of fluoride supplement consumption one month before delivery. Approximately 5 ml breast milk and 5 ml blood samples were obtained from each participating mother at a hospital setting, where the mothers were scheduled for a regular hospital diet. The blood samples were centrifuged in fluoride-free heparinized polyethylene tubes and stored at −18°C until measurements were made. Breast milk samples were directly refrigerated as with blood samples until measurements. The fluoride concentrations of milk and blood samples were assessed using an ion-selective fluoride electrode combined with an ion analyzer.ResultsThe fluoride levels of the plasma and breast milk samples were measured as 0.017±0.011 ppm and 0.006±0.002 ppm, respectively. The fluoride concentration of plasma was significantly higher than that of breast milk (P<.01). Correlation analysis revealed a significant relation between the groups (P<.01).ConclusionA limited level of fluoride transmission from plasma to breast milk was detected. Nevertheless, a significant correlation between the fluoride concentrations of breast milk and plasma was evident.

Effect of new innovative restorative carbomised glass cement on intrapulpal temperature rise: an ex-vivo study Abstract: This study aimed to evaluate the temperature changes that occurred in the pulp chamber when using GCP Glass Carbomer Fill (GCP) and two different resin-modified glass-ionomer (RGI) restorative materials at different dentin thicknesses. A standardized Class I occlusal cavity with 1 mm or 2 mm dentin thickness was prepared in the extracted human molar teeth. RGI and GCP fills were placed in the cavities and cured with two different light-curing units. This study included a total of 120 samples, with 20 samples in each group. The pulp microcirculation method was used for measuring the intrapulpal temperature changes. Statistical analysis was performed using the two-way ANOVA and Tukey HSD multiple comparison tests. Statistically significant differences were observed between 1 mm and 2 mm dentin thicknesses (p < 0.001). The GCP groups (both 1 mm and 2 mm dentin thicknesses) exhibited higher temperatures than the other groups (p < 0.001), and Fuji II LC and Photac Fil Quick Aplicap showed similar values (p > 0.05). The highest temperature changes were observed with 1 mm dentin thickness. While RGI materials in both dentin thicknesses did not cause temperature changes that were harmful to the pulp, GCP CarboLED LCU caused the highest intrapulpal temperature rise, and these values were borderline harmful to the dental pulp.

Objectives. To measure the temperature increase induced during thermocure lamp setting reaction of glass carbomer and to compare it with those induced by visible light curing of a resin-modified glass ionomer and a polyacid-modified composite resin in primary and permanent teeth. Materials and Methods. Nonretentive class I cavities were prepared in extracted primary and permanent molars. Glass carbomer (GC) was placed in the cavity and set at 60°C for 60 sn using a special thermocure lamp. Resin-modified glass ionomer (RMGIC) and polyacid-modified composite resin (PMCR) were placed in the cavities and polymerized with an LED curing unit. Temperature increases during setting reactions were measured with a J-type thermocouple wire connected to a data logger. Data were examined using two-way analysis of variance and Tukey's honestly significant difference tests. Results. The use of GC resulted in temperature changes of 5.17 ± 0.92°C and 5.32 ± 0.90°C in primary and permanent teeth, respectively (p > 0.05). Temperature increases were greatest in the GC group, differing significantly from those in the PMCR group (p < 0.05). Conclusion. Temperature increases during polymerization and setting reactions of the materials were below the critical value in all groups. No difference was observed between primary and permanent teeth, regardless of the material used.

No abstract

No abstract