Metal halide perovskites of the general formula ABX 3 -where A is a monovalent cation such as caesium, methylammonium or formamidinium; B is divalent lead, tin or germanium; and X is a halide anion-have shown great potential as light harvesters for thin-film photovoltaics [1][2][3][4][5] . Among a large number of compositions investigated, the cubic α-phase of formamidinium lead triiodide (FAPbI 3 ) has emerged as the most promising semiconductor for highly efficient and stable perovskite solar cells [6][7][8][9] , and maximizing the performance of this material in such devices is of vital importance for the perovskite research community. Here we introduce an anion engineering concept that uses the pseudo-halide anion formate (HCOO − ) to suppress anion-vacancy defects that are present at grain boundaries and at the surface of the perovskite films and to augment the crystallinity of the films. The resulting solar cell devices attain a power conversion efficiency of 25.6 per cent (certified 25.2 per cent), have long-term operational stability (450 hours) and show intense electroluminescence with external quantum efficiencies of more than 10 per cent. Our findings provide a direct route to eliminate the most abundant and deleterious lattice defects present in metal halide perovskites, providing a facile access to solution-processable films with improved optoelectronic performance.Perovskite solar cells (PSCs) have attracted much attention since their first demonstration in 2009 [1][2][3][4][5] . The rapid expansion of research into PSCs has been driven by their low-cost solution processing and attractive optoelectronic properties, including a tunable bandgap 6 , high absorption coefficient 10 , low recombination rate 11 and high mobility of charge carriers 12 . Within a decade, the power conversion efficiency (PCE) of single-junction PSCs progressed from 3% to a certified value of 25.5% 13 , the highest value obtained for thin-film photovoltaics. Moreover, through the use of additive and interface engineering strategies, the long-term operational stability of PSCs now exceeds 1,000 hours in full sunlight 14,15 . PSCs therefore show great promise for deployment as the next generation of photovoltaics.Compositional engineering plays a key part in achieving highly efficient and stable PSCs. In particular, mixtures of methylammonium lead triiodide (MAPbI 3 ) with formamidinium lead triiodide (FAPbI 3 ) have been extensively studied 5,7 . Compared to MAPbI 3 , FAPbI 3 is thermally more stable and has a bandgap closer to the Shockley-Queisser limit 6 , rendering FAPbI 3 the most attractive perovskite layer for single-junction PSCs.Unfortunately, thin FAPbI 3 films undergo a phase transition from the black α-phase to a photoinactive yellow δ-phase below a temperature of 150 °C. Previous approaches to overcome this problem have included mixing FAPbI 3 with a combination of methylammonium (MA + ), caesium (Cs + ) and bromide (Br − ) ions; however, this comes at the cost of blue-shifted absorbance and phase segregation under...

Improvements to perovskite solar cells (PSCs) have focused on increasing their power conversion efficiency (PCE) and operational stability and maintaining high performance upon scale-up to module sizes. We report that replacing the commonly used mesoporous–titanium dioxide electron transport layer (ETL) with a thin layer of polyacrylic acid–stabilized tin(IV) oxide quantum dots (paa-QD-SnO 2 ) on the compact–titanium dioxide enhanced light capture and largely suppressed nonradiative recombination at the ETL–perovskite interface. The use of paa-QD-SnO 2 as electron-selective contact enabled PSCs (0.08 square centimeters) with a PCE of 25.7% (certified 25.4%) and high operational stability and facilitated the scale-up of the PSCs to larger areas. PCEs of 23.3, 21.7, and 20.6% were achieved for PSCs with active areas of 1, 20, and 64 square centimeters, respectively.

Mixtures of cations or halides with FAPbI3 (where FA is formamidinium) lead to high efficiency in perovskite solar cells (PSCs) but also to blue-shifted absorption and long-term stability issues caused by loss of volatile methylammonium (MA) and phase segregation. We report a deposition method using MA thiocyanate (MASCN) or FASCN vapor treatment to convert yellow δ-FAPbI3 perovskite films to the desired pure α-phase. NMR quantifies MA incorporation into the framework. Molecular dynamics simulations show that SCN– anions promote the formation and stabilization of α-FAPbI3 below the thermodynamic phase-transition temperature. We used these low-defect-density α-FAPbI3 films to make PSCs with >23% power-conversion efficiency and long-term operational and thermal stability, as well as a low (330 millivolts) open-circuit voltage loss and a low (0.75 volt) turn-on voltage of electroluminescence.

Passivation of interfacial defects serves as an effective means to realize highly efficient and stable perovskite solar cells (PSCs). However, most molecular modulators currently used to mitigate such defects form poorly conductive aggregates at the perovskite interface with the charge collection layer, impeding the extraction of photogenerated charge carriers. Here, a judiciously engineered passivator, 4‐tert‐butyl‐benzylammonium iodide (tBBAI), is introduced, whose bulky tert‐butyl groups prevent the unwanted aggregation by steric repulsion. It is found that simple surface treatment with tBBAI significantly accelerates the charge extraction from the perovskite into the spiro‐OMeTAD hole‐transporter, while retarding the nonradiative charge carrier recombination. This boosts the power conversion efficiency (PCE) of the PSC from ≈20% to 23.5% reducing the hysteresis to barely detectable levels. Importantly, the tBBAI treatment raises the fill factor from 0.75 to the very high value of 0.82, which concurs with a decrease in the ideality factor from 1.72 to 1.34, confirming the suppression of radiation‐less carrier recombination. The tert‐butyl group also provides a hydrophobic umbrella protecting the perovskite film from attack by ambient moisture. As a result, the PSCs show excellent operational stability retaining over 95% of their initial PCE after 500 h full‐sun illumination under maximum‐power‐point tracking under continuous simulated solar irradiation.

To develop photosensitizers with high open-circuit photovoltage (Voc) is a crucial strategy to enhance the power conversion efficiency (PCE) of co-sensitized solar cells. Here, we show a judiciously tailored organic photosensitizer, coded MS5, featuring the bulky donor N-(2’,4’-bis(dodecyloxy)-[1,1’-biphenyl]-4-yl)-2’,4’-bis(dodecyloxy)-N-phenyl-[1,1’-biphenyl]-4-amine and the electron acceptor 4-(benzo[c][1,2,5]thiadiazol-4-yl)benzoic acid. Employing MS5 with a copper (II/I) electrolyte enables a dye-sensitized solar cell (DSC) to achieve a strikingly high Voc of 1.24 V, with the Voc deficit as low as 130 mV and an ideality factor of merely 1.08. The co-sensitization of MS5 with the wider spectral-response dye XY1b produces a highly efficient and stable DSC with the PCE of 13.5% under standard AM1.5 G, 100 mW cm−2 solar radiation. Remarkably, the co-sensitized solar cell (active area of 2.8 cm2) presents a record PCE of 34.5% under ambient light, rendering it very attractive as an ambient light harvesting energy source for low power electronics.

As a result of their attractive optoelectronic properties, metal halide APbI3 perovskites employing formamidinium (FA+) as the A cation are the focus of research. The superior chemical and thermal stability of FA+ cations makes α‐FAPbI3 more suitable for solar‐cell applications than methylammonium lead iodide (MAPbI3). However, its spontaneous conversion into the yellow non‐perovskite phase (δ‐FAPbI3) under ambient conditions poses a serious challenge for practical applications. Herein, we report on the stabilization of the desired α‐FAPbI3 perovskite phase by protecting it with a two‐dimensional (2D) IBA2FAPb2I7 (IBA=iso‐butylammonium overlayer, formed via stepwise annealing. The α‐FAPbI3/IBA2FAPb2I7 based perovskite solar cell (PSC) reached a high power conversion efficiency (PCE) of close to 23 %. In addition, it showed excellent operational stability, retaining around 85 % of its initial efficiency under severe combined heat and light stress, that is, simultaneous exposure with maximum power tracking to full simulated sunlight at 80 °C over 500 h.

Five novel perylene molecules with different intramolecular charge-transfer (ICT) characters have been synthesized. The relation between the ICT character for different donating groups and the results for their electro- and photochemical properties as well as their performance in nanostructured dye-sensitized solar cells (nDSC) are reported. With the stronger donors, we obtain a shift of the lowest unoccupied molecular orbital (LUMO) to more negative potential versus normal hydrogen electrode (NHE) as well as an increase the charge separation in the dye upon excitation. Ab initio calculations were used to analyze the effects on orbital energies and electron distribution with the different donors. Incorporating the dyes in nDSCs, we see a drastical improvement in the performance for the more polar dyes. In particular, we find a much improved photovoltage because of higher LUMO levels, allowing conduction band tuning in the TiO2 as well as a contribution from the permanent dipoles in the dyes. The photocurrent improves remarkably with increasing ICT character of the dyes. The external quantum efficiency reached over 70%, and the overall solar-to-electrical energy conversion efficiency was improved to almost 4% for the dye with highest ICT character, which can be compared with devices with the standard N719 dye (Ru(dcbpy)2(NCS)2) showing 6% under similar conditions. The performance is a significant improvement compared to previous reports for perylenes and lifts the performance from modest to promising. Initial stability tests show that the dye with the highest performance was spectrally stable after more than 2000 h of irradiation in a solar-cell device.

No abstract