The measurement of strain in structural elements is a necessary means of investigating the condition of a structure, both in research and in practice. The measurement methods for recording strain considered in this work represent both well-established techniques (strain gauges), as well as techniques that are part of rather current research streams (fiber optic sensors, digital image correlation). This work's contribution lies in providing an overarching comparison of these approaches, thereby informing practitioners and researchers as to parameters concerning their assembly, application, and their accuracy. To such ends, two test series were carried out, one on RC tension rods and another on a RC beam in a four-point bending test. From the latter scenario, for example, certain generalizations were to be deduced for varying load levels: low strains are measured well using the fiber optic technique. Conversely, digital image correlation was discovered to be an adequate choice when assessing higher strain levels and concomitant concrete cracking, as this non-contact technique avoids imprecisions caused by adhesives. Findings are to assist the future user by contrasting the three techniques in terms of assembly, handling, application and resilience of sensors, external influences as well as measurement resolution and accuracy. Such practice-oriented remarks should simplify a selection of the suitable measurement techniques catering to the respective, context-dependent testing scenario.
Due to the high sensitivity of coda waves to the smallest structural alterations such as strain, humidity or temperature changes, ultrasonic waves are a valid means to examine entire structures employing networks of ultrasonic transducers. In order to substantiate this ex ante assessment, the viability of measuring ultrasonic waves as a valid point of reference and inference for structural changes is to be further scrutinized in this work. In order to investigate the influence of mechanical strain on ultrasonic signals, a four-point bending test was carried out on a reinforced concrete beam at Ruhr University Bochum. Thus, measurements collected from a network of selected transducer pairings arranged across the central, shear-free segment of the test specimen, were correlated to their respective strain fields. Detected ultrasonic signals were evaluated employing Coda Wave Interferometry. Such analysis comprised the initial non-cracked state as well as later stages with incremental crack depth and quantity. It was to ascertain that the test specimen can in fact be qualitatively compartmentalized into areas of compression and tension identified via Relative Velocity Changes presented in Attribute Maps. However, since results did not entail a zero crossing, i.e., neither positive nor negative values were to be calculated, only relative changes in this work displayed staggered over the height of the object under test, are discussed. Under the given methodological premises, additional information is currently required to make quantitative assertions regarding this correlation of ultrasonic and strain results. This holds true for the comparability of the ultrasonic and strain results for both non-cracked and even the cracked state.
Zusammenfassung Faseroptische Messsysteme ermöglichen eine nahezu kontinuierliche Aufnahme von Dehnung und Temperatur entlang einer Messfaser. Zur Dehnungsmessung sollte die Faser mit einem Klebstoff direkt auf dem Bauteil appliziert werden, bei Temperaturmessungen in der Regel geschützt und verbundlos in Kapillaren geführt sein. Feldartige, zweidimensionale Aufnahmen entstehen entweder, wenn die Fasern kreuzweise gerastert angeordnet sind oder aus Interpolationen zwischen mehreren, nach den erwarteten Gradienten gestaffelten Fasern einer Verlegerichtung. Der Beitrag stellt die grundlegenden Messprinzipien der Faseroptik, erzielbare Genauigkeiten, geeignete Applikationen in Stahlbetonbauteilen und die feldartige Messung von Dehnungen oder Temperaturen vor. Beispiele der Dehnungsmessung an Ankerschienen und der Temperaturfeldaufnahme in einem Stahlbetonbalken zeigen die praktische Anwendung.
Reinforced concrete is a widely used construction material in the building industry. With the increasing age of structures and higher loads there is an immense demand for structural health monitoring of built infrastructure. Coda wave interferometry is a possible candidate for damage detection in concrete whose applicability is demonstrated in this study. The technology is based on a correlation evaluation of two ultrasonic signals. In this study, two ways of processing the correlation data for damage detection are compared. The coda wave measurement data are obtained from a four-point bending test at a reinforced concrete specimen that is also instrumented with fibre optic strain measurements. The used ultrasonic signals have a central frequency of 60 kHz which is a significant difference to previous studies. The experiment shows that the coda wave interferometry has a high sensitivity for developing cracks and by solving an inverse problem even multiple cracks can be distinguished. A further specialty of this study is the use of finite elements for solving a diffusion problem which is needed to state the previously mentioned inverse problem for damage localization.
The integral collection of information such as strains, cracks, or temperatures by ultrasound offers the best prerequisites to monitor structures during their lifetime. In this paper, a novel approach is proposed which uses the collected information in the coda of ultrasonic signals to infer the condition of a structure. This approach is derived from component tests on a reinforced concrete beam subjected to four-point bending in the lab at Ruhr University Bochum. In addition to ultrasonic measurements, strain of the reinforcement is measured with fiber optic sensors. Approached by the methods of moment-curvature relations, the steel strains serve as a reference for velocity changes of the coda waves. In particular, a correlation between the relative velocity change and the average steel strain in the reinforcement is derived that covers 90% of the total bearing capacity. The purely empirical model yields a linear function with a high level of accuracy (R2 = 0.99, RMSE≈90μstrain).
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.