No abstract

No abstract

No abstract

Due to its wide applicability in industry, devising microstructures on the surface of materials can be easily implemented and automated in technological processes. Laser Surface Texturing (LST) is applied to modify the chemical composition, morphology, and roughness of surfaces (wettability), cleaning (remove contaminants), reducing internal stresses of metals (hardening, tempering), surface energy (polymers, metals), increasing the adhesion (hybrid joining, bioengineering) and decreasing the growth of pathogenic bacteria (bioengineering). This paper is a continuation and extension of our previous studies in laser-assisted texturing of surfaces. Three different patterns (crater array-type C, two ellipses at 90° overlapping with its mirror-type B and 3 concentric octagons-type A) were applied with a nanosecond pulsed laser (active medium Nd: Fiber Diode-pumped) on the surface of a ferritic stainless steel (AISI 430). Micro texturing the surface of a material can modify its wettability behavior. A hydrophobic surface (contact angle greater than 90°) was obtained with different variations depending on the parameters. The analysis performed in this research (surface roughness, wettability) is critical for assessing the surface functionality, characteristics and properties of the stainless steel surface after the LST process. The values of the surface roughness and the contact angle are directly proportional to the number of repetitions and inversely proportional to the speed. Recommendations for the use of different texturing pattern designs are also made.

This paper reports the obtaining of poly (vinyl alcohol) and ι-carrageenan blend hydrogels by physical crosslinking (consecutive freeze–thaw cycles). The two polymers were completely miscible in the weight ratio interval used in this study, as determined by solution viscometry data. Strong interactions through hydrogen bonding and forming of mixed interpolymer crystalline domains were observed, which are responsible for the formation of stable drug release-tunable matrices. The release profiles of three model antibiotic drugs (amoxicillin, tetracycline hydrochloride, and gentamicin sulfate) were assessed in a pH interval between 3 and 7.3. They were found to be strongly dependent on the drug chemistry, mesh size of the hydrogels, swelling mechanism, and pH of the release medium. A decrease of up to 40% in the release rates and up to 10% in the diffusion coefficients of the model drugs was registered with the increase in ι-carrageenan content.

No abstract

Laser surface texturing (LST) is a method to obtain micro-structures on the material’s surface for improving tribological performances, wetting tuning, surface treatment, and increasing adhesion. The material selected for LST is AISI 430 ferritic stainless steel, distinguished by the low cost in manufacturing, corrosion resistance, and high strength at elevated temperature. The present study addresses the morphology of new pattern designs (crater array, ellipse, and octagonal shapes). The patterns are applied on the stainless-steel surface by a non-contact method with high quality and precision nanosecond pulsed laser equipment. The investigation of laser parameter influence on thermal affected area and micro-structures is accomplished by morphological and elemental analysis (SEM + EDX). The parameters of the laser micro-patterning have a marked influence on the morphology, creating groove-type sections with different depths and recast material features. From the SEM characterization, the highest level of recast material is observed for concentric octagon LST design. Its application is more recommended for the preparation of the metal surface before hybrid welding. Additionally, the lack of the oxygen element in the case of this design suggests the possible use of the pattern in hybrid joining.

In this work, the corrosion behavior of NiCr(Ti) protective coatings deposited on mild steel substrates through laser cladding technology is studied as an alternative new material for metallic bipolar plates used in PEMFC applications. For electrochemical testing, a solution consisting of 0.5 M H2SO4 + 2 ppm F− at room temperature is used as an electrolyte. The fluoride ions are added to simulate the conditions in the PEM fuel cell due to degradation of the proton exchange membrane and fluoride release. A saturated calomel electrode (SCE) is used as a reference electrode and a platinum mesh as the counter electrode. Scanning electron microscopy (SEM) and optical microscopy (OM) are used for studying the morphology of the protective coatings and the effect of Ti addition. The electrochemical evaluation consisted of measuring the open circuit potential (OCP), followed by electrochemical impedance spectroscopy measurements (EIS) and potentiodynamic polarization. It is found that the coatings with 5% Ti, 7% Ti and 10% Ti addition comply with the conditions of the US DOE regarding corrosion performance to be used as materials for the manufacture of the bipolar plates.