We report a method for fabricating optical quality silica and silica-titania glasses by additive manufacturing, or 3D printing. Key to this success was the combination of sol-gel derived silica and silica-titania colloidal feedstocks, 3D direct ink writing (DIW) technology, and conventional glass thermal processing methods. Printable silica and silica-titania sol inks were prepared directly from molecular precursors by a simple one-pot method, which was optimized to yield viscous, shear-thinning colloidal suspensions with tuned rheology ideal for DIW. After printing, the parts were dried and sintered under optimized thermal conditions to ensure complete organic removal and uniform densification without crystallization.Characterizations of the 3D-printed pure silica and silica-titania glasses show that they are This article is protected by copyright. All rights reserved. 2 equivalent to commercial optical fused silica (Corning ® 7980) and silica-titania glasses (Corning ULE ® 7972). More specifically, they exhibit comparable chemical composition, SiO 2 network structure, refractive index, dispersion, optical transmission, and coefficient of thermal expansion. 3D printed silica and silica-titania glasses also exhibited comparable polished surface roughness and meet refractive index homogeneity standards within range of commercial optical grade glasses. This method establishes 3D printing as a viable tool to create optical glasses with compositional and geometric configurations that are inaccessible by conventional optical fabrication methods. † denotes value determined by LA-ICP-MS; a-SiO 2 used to represent amorphous SiO 2

molding have been demonstrated for fabricating complex glass structures. [11][12][13][14][15][16][17][18] However, there are limitations to these methods. In binder jetting, the sintered glasses can be fragile and appear opaque due to incomplete densification. Methods to print glass directly (e.g., fused deposition or filament feed) require high temperatures to melt the silica feedstock, resulting in filaments that are potentially vulnerable to thermal stresses and unable to completely merge into the desired structure, which may limit the printing speed and resolution of the printed parts. Soft replication molding cannot be used to produce gap-spanning features, and pseudo-3D objects (i.e., stacked assemblies of thin molded sheets) can only be formed by precisely aligning layers that must then be bonded during heat treatment. None of these methods have been shown to produce glasses that are simultaneously transparent, free form, and 3D with sub-millimeter features.We have developed a two-part process (forming and sintering) which uses direct ink writing (DIW) for the 3D printing of optically transparent glass structures with sub-millimeter features. DIW is a layer-by-layer assembly technique in which shear-thinning inks are extruded through a nozzle in a programmable pattern, upon which the inks rapidly solidify via gelation, evaporation, or temperature-induced phase change. [19] DIW has been used in a wide range of applications such as polymeric optical wave guides, complex scaffolds, 3D periodic graphene aerogels, and self-healing materials. [6,[20][21][22][23][24] Our process first relies on DIW printing of colloidal silica suspensions to form silica green bodies (porous, low density structures) of the desired shape. A key feature of this process is the ability to control yield stress and shear thinning to obtain ink properties best suited for specific applications of the printed glass. Second, the printed structures are dried and heated to temperatures below the melting point of silica to sinter the green body into a fully dense, amorphous, transparent solid structure (Figure 1). In contrast to direct 3D printing of molten glass, this two-step approach does not require high temperatures during printing and allows for higher resolution features, due to both the ability to extrude thinner filaments and the shrinkage that occurs during the densification stage.The critical challenges in formulating a suitable ink for formation of the silica green bodies toward glass structures are: i) the ink must possess the desired rheological behavior for printing and shape retention, and ii) the ink must be able to dry without cracking while still maintaining open porosity that Silica inks are developed, which may be 3D printed and thermally processed to produce optically transparent glass structures with sub-millimeter features in forms ranging from scaffolds to monoliths. The inks are composed of silica powder suspended in a liquid and are printed using direct ink writing. The printed structures are then dried and sintered ...

Purpose-designed, water-lean solvents have been developed to improve the energy efficiency of CO capture from power plants, including CO-binding organic liquids (COBOLs) and ionic liquids (ILs). Many of these solvents are highly viscous or change phases, posing challenges for conventional process equipment. Such problems can be overcome by encapsulation. Micro-Encapsulated CO Sorbents (MECS) consist of a CO-absorbing solvent or slurry encased in spherical, CO-permeable polymer shells. The resulting capsules have diameters in the range of 100-600 μm, greatly increasing the surface area and CO absorption rate of the encapsulated solvent. Encapsulating these new solvents requires careful selection of shell materials and fabrication techniques. We find several common classes of polymers are not compatible with MECS production, but we develop two custom formulations, a silicone and an acrylate, that show promise for encapsulating water-lean solvents. We make the first demonstration of an encapsulated IL for CO capture. The rate of CO absorption is enhanced by a factor of 3.5 compared to a liquid film, a value that can be improved by further development of shell materials and fabrication techniques.

We demonstrate an additive manufacturing approach to produce gradient refractive index glass optics. Using direct ink writing with an active inline micromixer, we three-dimensionally print multimaterial green bodies with compositional gradients, consisting primarily of silica nanoparticles and varying concentrations of titania as the index-modifying dopant. The green bodies are then consolidated into glass and polished, resulting in optics with tailored spatial profiles of the refractive index. We show that this approach can be used to achieve a variety of conventional and unconventional optical functions in a flat glass component with no surface curvature.

Direct ink writing (DIW) three-dimensional (3D) printing provides a revolutionary approach to fabricating components with gradients in material properties. Herein, we report a method for generating colloidal germania feedstock and germania–silica inks for the production of optical quality germania–silica (GeO2–SiO2) glasses by DIW, making available a new material composition for the development of multimaterial and functionally graded optical quality glasses and ceramics by additive manufacturing. Colloidal germania and silica particles are prepared by a base-catalyzed sol–gel method and converted to printable shear-thinning suspensions with desired viscoelastic properties for DIW. The volatile solvents are then evaporated, and the green bodies are calcined and sintered to produce transparent, crack-free glasses. Chemical and structural evolution of GeO2–SiO2 glasses is confirmed by nuclear magnetic resonance, X-ray diffraction, and Raman spectroscopy. UV–vis transmission and optical homogeneity measurements reveal comparable performance of the 3D printed GeO2–SiO2 glasses to glasses produced using conventional approaches and improved performance over 3D printed TiO2–SiO2 inks. Moreover, because GeO2–SiO2 inks are compatible with DIW technology, they offer exciting options for forming new materials with patterned compositions such as gradients in the refractive index that cannot be achieved with conventional manufacturing approaches.

No abstract

We present a multilayer dropmaker geometry that enables the modular fabrication of microfluidic devices containing precisely patterned channel surface wettability. The platform is used for the scalable production of uniform double emulsion drops.

A lack of predictive methodology is frequently a major bottleneck in materials development for additive manufacturing. Hence, exploration of new printable materials often relies on the serendipity of trial and error approaches, which is time-consuming, labor-intensive, and costly. We present an approach to overcome these issues by quantifying and controlling the viscoelasticity of inks for multimaterial 3D printing of silica–titania glass using direct ink writing (DIW). We formulate simple silica and silica–titania inks from a suspension of fumed silica nanoparticles in an organic solvent with a dissolved molecular titania precursor. We use a small set of experimental rheological data and estimates of interaction potentials from colloidal theory to develop a predictive tool that allows us to design and obtain compatible inks that are matched both in desired rheological properties (viscosity profiles and elastic modulus) as well as solids loading. The model incorporates silica particle volume fraction, particle size, particle size distribution, and titania precursor concentration, and captures the effects of all formulation parameters on the measured viscoelasticity in a single curve. We validate the ink formulations predicted by the model and find that the materials can be very well matched in rheological properties as desired for 3D printing. Using the DIW and heat treatment methods we have reported previously, we use these inks to print and process a fully transparent glass with spatial change in dopant composition and refractive index. We believe that this approach can be extended to other colloidal systems and allow predictive ink formulation design for desired printability in direct ink write manufacturing.