ResumoNeste trabalho foi avaliada a utilização de dregs, um resíduo sólido inorgânico proveniente do processo Kraft, como matéria-prima alternativa em cerâmica vermelha. As matérias-primas foram caracterizadas por fluorescência de raios X, difração de raios X, distribuição de tamanho de partículas, análise térmica diferencial e termogravimétrica. Os corpos de prova com adições de até 40% em massa do resíduo foram conformados por prensagem uniaxial e sinterizados a 850 e 950 °C, sendo então determinadas as seguintes propriedades físico-mecânicas: resistência à flexão, retração linear, absorção de água, porosidade aparente, massa específica aparente e perda ao fogo. Também foi feita análise das fases desenvolvidas durante a sinterização e da microestrutura final por difração de raios X e microscopia eletrônica de varredura, respectivamente. Os resultados mostraram que a incorporação de até 20% em massa de dregs não interferiu na resistência à flexão da massa, sendo possível sua utilização em substituição parcial da argila. Palavras-chave: cerâmica vermelha, resíduos industriais, dregs. AbstractIn this paper the use of dregs, an inorganic solid waste generated by Kraft process, as an alternative raw material in red ceramic was evaluated. The raw materials, dregs and clay, were characterized by X-ray fluorescence, X-ray diffraction, particle size distribution by laser diffraction, differential thermal analysis and thermogravimetry. Formulations with varying dregs content between 0 and 40 wt% were prepared. The plasticity of mixtures was evaluated by Atterberg method. Specimens were obtained by uniaxial pressing and fired at 850 and 950 °C, then the following physicalmechanical properties were determined: flexural strength, firing shrinkage, water absorption, open porosity, bulk density and loss on ignition. Crystalline phases developed during sintering and final microstructure were evaluated by X-ray diffraction and scanning electron microscopy, respectively. The results showed that incorporation of dregs until 20 wt% did not affect flexural strength, being possible its use in partial replacement of clay.
Direitos para esta edição cedidos à Atena Editora pelos autores. Todo o conteúdo deste livro está licenciado sob uma Licença de Atribuição Creative Commons. Atribuição-Não-Comercial-NãoDerivativos 4.0 Internacional (CC BY-NC-ND 4.0).O conteúdo dos artigos e seus dados em sua forma, correção e confiabilidade são de responsabilidade exclusiva dos autores, inclusive não representam necessariamente a posição oficial da Atena Editora. Permitido o download da obra e o compartilhamento desde que sejam atribuídos créditos aos autores, mas sem a possibilidade de alterá-la de nenhuma forma ou utilizá-la para fins comerciais. Todos os manuscritos foram previamente submetidos à avaliação cega pelos pares, membros do Conselho Editorial desta Editora, tendo sido aprovados para a publicação com base em critérios de neutralidade e imparcialidade acadêmica.A Atena Editora é comprometida em garantir a integridade editorial em todas as etapas do processo de publicação, evitando plágio, dados ou resultados fraudulentos e impedindo que interesses financeiros comprometam os padrões éticos da publicação. Situações suspeitas de má conduta científica serão investigadas sob o mais alto padrão de rigor acadêmico e ético.
ResumoAtualmente, diversos segmentos industriais têm buscado alternativas à disposição dos resíduos sólidos gerados. Contudo, alguns resíduos industriais são de difícil reaproveitamento, como o dregs, originado durante o processo Kraft de fabricação de celulose, e o resíduo de beneficiamento de vidros planos. Assim, este trabalho teve o objetivo de caracterizar ambos resíduos e uma argila, visando avaliar a potencialidade da incorporação dos resíduos em massas argilosas para fabricação de produtos de cerâmica vermelha. Os resíduos e a argila foram secos, destorroados e submetidos às seguintes técnicas de caracterização: análise granulométrica, fluorescência de raios X, difração de raios X e análise térmica diferencial e termogravimétrica. Ambos resíduos apresentaram alta concentração de óxidos alcalinos ou alcalino-terrosos, indicando a possibilidade da formulação de massas utilizando-os como matérias-primas alternativas, em função de elevarem a proporção de óxidos fundentes da massa, presentes em baixos teores na argila avaliada. Abstract Nowadays, some industries have been looking for alternatives to solid wastes disposal. Although, there are industrial wastes that are hard to reutilize, e. g., dregs, from Kraft process, and flat glass cutting waste. Therefore, the aim of this study was characterized both wastes in order to evaluate its potentiality to incorporate in red clay. Wastes and clay were dried and ground, then they were subjected to the following techniques: particle size analysis, X ray fluorescence, X ray diffraction, differential thermal analysis and thermogravimetric analysis. Both wastes showed high alkali or alkaline-earth oxide contents, indicating the possibility to use them as alternative raw material to prepare clayey products, due to increase the flux content in the mixture, which are in low percentage in clay.
Resumo O objetivo deste trabalho foi desenvolver um compósito permeável formado por uma matriz de polipropileno reforçada com resíduos de construção e demolição (RCD). Inicialmente foi feita a limpeza, peneiramento e caracterização do RCD. O compósito foi conformado na forma de placas pelo processo de compressão a quente. O RCD foi misturado com os grânulos do polímero e a mistura disposta em um molde que foi fechado e comprimido com carga de 1 ton e mantido na temperatura de 210 o C por 10 min. Foram conformadas placas permeáveis e impermeáveis variando-se o percentual dos constituintes e granulometria do RCD. Para a caracterização foram realizados ensaios de permeabilidade e flexão em três pontos. As placas permeáveis apresentaram elevado grau de permeabilidade, muito superior aos requisitos mínimos para concreto. Foi constatado que a distribuição granulométrica tem influência na resistência mecânica e permeabilidade do compósito. O aumento do teor de granulados finos promoveu aumento nas propriedades mecânicas em flexão sem perda da permeabilidade. Com a impermeabilização das placas e consequente redução de vazios as propriedades mecânicas em flexão praticamente triplicaram. Analisando os resultados de uma forma geral pode-se concluir que há margem para melhorar o desempenho mecânico do compósito sem perda da permeabilidade. Palavras-chave: Resíduos de construção e demolição; Compósitos poliméricos; Permeabilidade.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.