Background:To compare 4% articaine and 2% lidocaine local anesthetics in achieving pulpal anesthesia of the lower first permanent molar teeth objectively, and to assess and compare lip and lingual mucosa numbness subjectively.Materials and Methods:All subjects received 1.7 ml of any one anesthetic in the mucobuccal fold adjacent to mandibular first molar teeth; the same individuals received the second infiltration at least 1 week after the first. Later, comparisons for pulpal anesthesia, lip and lingual mucosa numbness between these two anesthetics solutions were made.Results:Articaine showed significant results with P = 0.006 in achieving pulpal anesthesia objectively, when compared with lidocaine. Articaine also showed very high significant results subjectively with P = 0.0006 in achieving lip numbness, when compared with lidocaine. But the results in achieving lingual mucosa numbness with articaine subjectively was not significant with P = 0.01, when compared with lidocaine.Conclusion:Endodontic and operative treatments are one of the most common oral non-surgical procedures done under local anesthesia. The diversity of anesthetic substances currently available on the market requires dental professionals to assess the drug both by its pharmacokinetic and also by its clinical characteristics during dental treatments. Our study used 4% articaine, which is available in the market, for comparison with 2% lidocaine. Further studies are required to use an equal concentration of solutions to achieve more accurate results.

Aim:The aim of this study is to compare the shear bond strengths of conventional resin cement and self-adhesive resin cement bonded to lithium disilicate. Materials and methods:A total of 40 extracted human molar teeth were mounted in self-cure acrylic resin. Teeth were prepared to obtain flat occlusal surface. About 40 lithium disilicate specimens of dimension-10 mm in diameter and thickness of 2 mm-were fabricated using lost wax technique. The samples were divided into four groups: Groups I, II, III, and IV (n = 10). The specimens were surface treated with Monobond S silane coupling agent. Self-etching primer and bonding agent were applied on the bonding surface of the teeth in groups I and III. The specimens were bonded to the primed teeth with the Multilink N resin cement and subjected to the universal testing machine. The specimens were light-cured. Specimens in groups II and IV were luted to teeth using self-adhesive cement RelyX U100. The same force was applied over the specimen as mentioned above. Excess cement was removed, and light curing was done. The specimens in groups III and IV were subjected to thermocycling for 10,000 cycles at temperatures altering between 5°C and 55°C. Results:The shear bond strengths of conventional resin cement and self-adhesive resin cement with lithium disilicate were tested before and after thermocycling. Department of Pediatric and Preventive Dentistry, Sri Sankara Dental College, Thiruvananthapuram, Kerala, India Corresponding Author: Anip K Roy, Department of Prosthodontics, Purvanchal Institute of Dental Sciences Gorakhpur, Uttar Pradesh, India, e-mail: royanip86@gmail.com thermocycling has no significant effect on the bond strengths of conventional or self-adhesive resin cement. However, from the study, it is seen that conventional resin cement had a higher shear bond strength value than the self-adhesive resin cement. Conclusion:There was a significant difference between the average shear bond strength values of conventional resin cement (Multilink N) and self-adhesive resin cement (RelyX U100) when bonded to lithium disilicate disks, and thermocycling had no significant effect on the bond strength of conventional or self-adhesive resin cements.Clinical significance: Among all-ceramic systems available, lithium disilicate materials have emerged as an excellent esthetic material for fabrication of anterior and posterior crowns and three-unit anterior fixed partial dentures because of their high translucency and improved optical properties. For successful clinical outcomes, the luting agent should have high bond strength not only to the ceramic surface, but also to the tooth surface.

No abstract

Conclusion: The present study concluded that fracture resistance was more in zirconia posts than metal as well as glass posts in the teeth that have undergone endodontic therapy.