Solution-processable perovskite materials have garnered tremendous attention because of their excellent charge carrier mobility, possibility of a tunable optical bandgap, and high photoluminescence quantum efficiency (PLQE). In particular, the uniform morphology of a perovskite film is the most important factor in realizing perovskite light-emitting diodes (PeLEDs) with high efficiency and full-coverage electroluminescence (EL). In this study, we demonstrate highly efficient PeLEDs that contain a perovskite film with a uniform morphology by introducing HBr into the perovskite precursor. The introduction of HBr into the perovskite precursor results in a perovskite film with a uniform, continuous morphology because the HBr increases the solubility of the inorganic component in the perovskite precursor and reduces the crystallization rate of the perovskite film upon spin-coating. Moreover, PeLEDs fabricated using perovskite films with a uniform, continuous morphology, which were deposited using 6 vol% HBr in a dimethylformamide (DMF)/hydrobromic acid (HBr) cosolvent, exhibited full coverage of the green EL emission. Finally, the optimized PeLEDs fabricated with perovskite films deposited using the DMF/HBr cosolvent exhibited a maximum luminance of 3490 cd m(-2) (at 4.3 V) and a luminous efficiency of 0.43 cd A(-1) (at 4.3 V).

Highly efficient planar perovskite optoelectronic devices are realized by amine-based solvent treatment on compact TiO2 and by optimizing the morphology of the perovskite layers. Amine-based solvent treatment between the TiO2 and the perovskite layers enhances electron injection and extraction and reduces the recombination of photogenerated charges at the interface.

A perovskite LED with a perovskite film treated under optimum thermal annealing conditions exhibits a significantly enhanced long-term stability with full coverage of the green electroluminescence emission due to the highly uniform morphology of the perovskite film.

Metal halide perovskites (MHPs) have emerged as promising emitters because of their excellent optoelectronic properties, including high photoluminescence quantum yields (PLQYs), wide‐range color tunability, and high color purity. However, a fundamental limitation of MHPs is their low exciton binding energy, which results in a low radiative recombination rate and the dependence of PLQY on the excitation intensity. Under the operating conditions of light‐emitting diodes (LEDs), the injected current densities are typically lower than the trap density, leading to a low actual PLQY. Moreover, the defects not only initiate the decomposition of MHPs caused by extrinsic factors, but also intrinsically stimulate ion migration across the interface and lead to the corrosion of electrodes due to interaction between those electrodes, even under inert conditions. The passivation of defects has proven to be effective for mitigating the effects of defects in MHPs. Herein, the origins and theoretical calculations of the defect tolerance in MHPs and the impact of defects on both the performance and stability of perovskite LEDs are reviewed. The passivation methods and materials for MHP bulk films and nanocrystals are discussed in detail. Based on the currently reported advances, specific requirements and future research directions for display applications are suggested.

Metal halide perovskites (MHPs) have emerged as promising materials for light‐emitting diodes owing to their narrow emission spectrum and wide range of color tunability. However, the low exciton binding energy in MHPs leads to a competition between the trap‐mediated nonradiative recombination and the bimolecular radiative recombination. Here, efficient and stable green emissive perovskite light‐emitting diodes (PeLEDs) with an external quantum efficiency of 14.6% are demonstrated through compositional, dimensional, and interfacial modulations of MHPs. The interfacial energetics and optoelectronic properties of the perovskite layer grown on a nickel oxide (NiOx) and poly(3,4‐ethylenedioxythiophene):polystyrene sulfonate hole injection interfaces are investigated. The better interface formed between the NiOx/perovskite layers in terms of lower density of traps/defects, as well as more balanced charge carriers in the perovskite layer leading to high recombination yield of carriers are the main reasons for significantly improved device efficiency, photostability of perovskite, and operational stability of PeLEDs.

This work reports the origin of high piezoelectricity of inorganic halide thin films poled at high fields along with the electromechanical energy-harvesting and motion-sensing performance.

We report highly efficient perovskite LEDs with a reduced hole injection barrier and improved crystallinity of perovskite using a PEDOT:MoO3 composite layer.

The beneficial use of a hole transport layer (HTL) as a substitution for poly(3,4-ethlyenedioxythiophene): polystyrene sulfonate (PEDOT:PSS) is regarded as one of the most important approaches for improving the stability and efficiency of inverted perovskite solar cells. Here, we demonstrate highly efficient and stable inverted perovskite solar cells by applying a GO-doped PEDOT:PSS (PEDOT:GO) film as an HTL. The high performance of this solar cell stems from the excellent optical and electrical properties of the PEDOT:GO film, including a higher electrical conductivity, a higher work function related to the reduced contact barrier between the perovskite layer and the PEDOT:GO layer, enhanced crystallinity of the perovskite crystal, and suppressed leakage current. Moreover, the device with the PEDOT:GO layer showed excellent long-term stability in ambient air conditions. Thus, the enhancement in the efficiency and the excellent stability of inverted perovskite solar cells are promising for the eventual commercialization of perovskite optoelectronic devices.