The oxygen evolution reaction (OER) has aroused extensive interest from materials scientists in the past decade by virtue of its great significance in the energy storage/conversion systems such as water splitting, rechargeable metal–air batteries, carbon dioxide (CO2) reduction, and fuel cells. Among all the materials capable of catalyzing OER, layered double hydroxides (LDHs) stand out as one of the most effective electrocatalysts owing to their compositional and structural flexibility as well as the tenability and the simplicity of their preparation process. For this reason, numerous efforts have been dedicated to adjusting the structure, forming the well‐defined morphology, and developing the preparation methods of LDHs to promote their electrocatalytic performance. In this article, recent advances in the rational design of LDH‐based electrocatalysts toward OER are summarized. Specifically, various tactics for the synthetic methods, as well as structural and composition regulations of LDHs, are further highlighted, followed by a discussion on the influential factors for OER performance. Finally, the remaining challenges to investigate and improve the catalyzing ability of LDH electrocatalysts are stated to indicate possible future development of LDHs.

Single-atom catalysts (SACs) have emerged as one of the most promising alternatives to noble metal-based catalysts for highly efficient oxygen reduction reaction (ORR). While SACs can offer notable benefits in terms of lowering overall catalyst cost, there is still room for improvement regarding catalyst activity. To this end, we designed and successfully fabricated an ORR electrocatalyst in which atomic clusters are embedded in an atomically dispersed Fe–N–C matrix (FeAC@FeSA–N–C), as shown by comprehensive measurements using aberration-corrected scanning transmission electron microscopy (AC-STEM) and X-ray absorption spectroscopy (XAS). The half-wave potential of FeAC@FeSA–N–C is 0.912 V (versus reversible hydrogen electrode (RHE)), exceeding that of commercial Pt/C (0.897 V), FeSA–N–C (0.844 V), as well as the half-wave potentials of most reported non-platinum-group metal catalysts. The ORR activity of the designed catalyst stems from single-atom active centers but is markedly enhanced by the presence of Fe nanoclusters, as confirmed by both experimental measurements and theoretical calculations.

The graphitic carbon nitride (g-C3N4) which is a two-dimensional conjugated polymer has drawn broad interdisciplinary attention as a low-cost, metal-free, and visible-light-responsive photocatalyst in the area of environmental remediation. The g-C3N4-based materials have excellent electronic band structures, electron-rich properties, basic surface functionalities, high physicochemical stabilities and are “earth-abundant.” This review summarizes the latest progress related to the design and construction of g-C3N4-based materials and their applications including catalysis, sensing, imaging, and white-light-emitting diodes. An outlook on possible further developments in g-C3N4-based research for emerging properties and applications is also included.

No abstract

One of the key challenges that hinders broad commercialization of proton exchange membrane fuel cells is the high cost and inadequate performance of the catalysts for oxygen reduction reaction (ORR)....

COMMUNICATIONwith the fl exible substrate, and almost no device degradation has been found under bending tests.

Water electrolysis is a promising source of hydrogen; however, technological challenges remain. Intensive efforts have focused on developing highly efficient and earth-abundant electrocatalysts for water splitting. An effective strategy is proposed, using a bifunctional tubular cobalt perselenide nanosheet electrode, in which the sluggish oxygen evolution reaction is substituted with anodic hydrazine oxidation so as to assist energy-efficient hydrogen production. Specifically, this electrode produces a current density of 10 mA cm at -84 mV for hydrogen evolution and -17 mV for hydrazine oxidation in 1.0 m KOH and 0.5 m hydrazine electrolyte. An ultralow cell voltage of only 164 mV is required to generate a current density of 10 mA cm for 14 hours of stable water electrolysis.

NiO nanoflakes are created with a simple hydrothermal method on 3D (three‐dimensional) graphene scaffolds grown on Ni foams by microwave plasma enhanced chemical vapor deposition (MPCVD). Such as‐grown NiO‐3D graphene hierarchical composites are then applied as monolithic electrodes for a pseudo‐supercapacitor application without needing binders or metal‐based current collectors. Electrochemical measurements impart that the hierarchical NiO‐3D graphene composite delivers a high specific capacitance of ≈1829 F g−1 at a current density of 3 A g−1 (the theoretical capacitance of NiO is 2584 F g−1). Furthermore, a full‐cell is realized with an energy density of 138 Wh kg−1 at a power density of 5.25 kW kg−1, which is much superior to commercial ones as well as reported devices in asymmetric capacitors of NiO. More attractively, this asymmetric supercapacitor exhibits capacitance retention of 85% after 5000 cycles relative to the initial value of the 1st cycle.