IBERSEIS, a 303 km long (20 s) deep seismic reflection profile, was acquired across the Variscan belt in SW Iberian Peninsula. The acquisition parameters were designed to obtain a high‐resolution crustal‐scale image of this orogen. The seismic profile samples three major tectonic terranes: the South Portuguese Zone, the Ossa‐Morena Zone, and the Central Iberian Zone, which were accreted in Late Paleozoic times. These terranes show a distinctive seismic signature, as do the sutures separating them. Late strike‐slip movements through crustal wedges are apparent in the seismic image and have strongly modified the geometry of sutures. The upper crust appears to be decoupled from the lower crust all along the seismic line, but some deformation has been accommodated at deeper levels. A sill‐like structure is imaged in the middle crust as a 1–2 s thick and 175 km long high‐amplitude conspicuous reflective band. It is interpreted as a great intrusion of mafic magma in a midcrustal decollement. Taking into account surface geological data and the revealed crustal architecture, a tectonic evolution is proposed for SW Iberia which includes transpressional collision interacting during Early Carboniferous with a mantle plume. The Moho can be identified along the entire transect as subhorizontal and located at 10 to 11 s, indicating a 30–35 km average crustal thickness. Its seismic signature changes laterally, being very reflective beneath the South Portuguese Zone and the Central Iberian Zone, but discontinuous and diffuse below the Ossa Morena Zone.

No abstract

More than 50000 tons of CO 2 have been injected at Ketzin into the Stuttgart Formation, a saline aquifer, at approximately 620 m depth, as of the summer 2011. We present here results from the 1 st repeat 3D seismic survey that was performed at the site in the autumn 2009, after about 22000 tons of CO 2 had been injected. We show here that rather complex time-lapse signatures of this CO 2 can be clearly observed within a radius of about 300 m from the injection well. The highly irregular amplitude response within this radius is attributed to the heterogeneity of the injection reservoir. Time delays to a reflection below the injection level are also observed. Petrophysical measurements on core samples and geophysical logging of CO 2 saturation levels allow an estimate of the total amount of CO 2 visible in the seismic data to be made. These estimates are somewhat lower than the actual amount of CO 2 injected at the time of the survey and they are dependent upon the choice of a number of parameters. In spite of some uncertainty, the close agreement between the amount injected and the amount observed is encouraging for quantitative monitoring of CO 2 storage site using seismic methods.

A 3D 25-fold seismic survey with a bin size of 12 by [Formula: see text] and about [Formula: see text] of subsurface coverage was acquired in 2005 near a former natural gas storage site west of Berlin, as part of the five-year EU funded [Formula: see text] project. Main objectives of the seismic survey were to verify earlier geologic interpretations of structure based on vintage 2D seismic and borehole data and to map, if possible, the reservoir pathways in which the [Formula: see text] will be injected at [Formula: see text] depth, as well as providing a baseline for future seismic surveys and planning of drilling operations. The uppermost [Formula: see text] are well imaged and show an anticlinal structure with an east-west striking central graben on its top that extendsdown to the target horizon. About [Formula: see text] of throwis seen on the bounding faults. No faults are imaged near the planned drill sites. Remnant gas, cushion and residual gas, is present near the top of the anticline in the depth interval of about [Formula: see text] and has a clear seismic signature; both higher amplitudes in the reservoir horizons and velocity pulldown are observed. Amplitude mapping of these remnant gas horizons shows that they do not extend as far south as the injection site, which is located on the southern flank of the anticline. Amplitude anomalies, gas chimneys along an east-west striking fault, show that the stored or remnant gas either has been or is presently migrating out of the reservoir formations. Summed amplitude mapping of the planned injection horizon indicates that this lithologically heterogeneous formation may be more porous at the injection site.

No abstract

No abstract

[1] Deep seismic reflection data acquired as part of the SW-Iberia EUROPROBE project across the transpressional Variscan orogen sample three tectonic terranes: the South Portuguese Zone, the Ossa-Morena Zone, and the Central Iberian Zone. The seismic data reveal the existence of a mid-crustal reflective body 140 km long and of variable thickness (up to 5 km), the Iberian Reflective body. The conductivity image provided by coincident MT soundings, the amplitude characteristics of the seismics, mineralization studies related to magmatic ore deposits, and the surface geology suggest that the IRB is a mantle-derived mafic intrusion. The geophysical, geological and petrological data suggest that the IRB is most probably an Early Carboniferous (approximately at 350 -340 Ma) mantle-derived intrusion possibly linked to plume activity that took place in Europe in the Carboniferous and Permian.

Due to high metal prices and increased difficulties in finding shallower deposits, the exploration for and exploitation of mineral resources is expected to move to greater depths. Consequently, seismic methods will become a more important tool to help unravel structures hosting mineral deposits at great depth for mine planning and exploration. These methods also can be used with varying degrees of success to directly target mineral deposits at depth. We review important contributions that have been made in developing these techniques for the mining industry with focus on four main regions: Australia, Europe, Canada, and South Africa. A wide range of case studies are covered, including some that are published in the special issue accompanying this article, from surface to borehole seismic methods, as well as petrophysical data and seismic modeling of mineral deposits. At present, high-resolution 2D surveys mostly are performed in mining areas, but there is a general increasing trend in the use of 3D seismic methods, especially in mature mining camps.