We present what we believe to be the first terawatt diode-pumped laser employing single-crystalline Yb:CaF(2) as the amplifying medium. A maximum pulse energy of 420 mJ at a repetition rate of 1 Hz was achieved by seeding with a stretched femtosecond pulse 2 ns in duration, preamplified to 40 mJ. After recompression, a pulse energy of 197 mJ and a duration of 192 fs were obtained, corresponding to a peak power of 1 TW. Furthermore, nanosecond pulses containing an energy of up to 905 mJ were generated without optical damage.

We present an ultrafast thin-disk based multipass amplifier operating at a wavelength of 1030 nm, designed for atmospheric research in the framework of the Laser Lightning Rod project. The CPA system delivers a pulse energy of 720 mJ and a pulse duration of 920 fs at a repetition rate of 1 kHz. The 240 mJ seed pulses generated by a regenerative amplifier are amplified to the final energy in a multipass amplifier via four industrial thin-disk laser heads. The beam quality factor remains ∼ 2.1 at the output. First results on horizontal long-range filament generation are presented.

No abstract

On the quest towards reaching petawatt-scale peak power light pulses with few-cycle duration, optical parametric chirped pulse amplification (OPCPA) pumped on a time scale of a few picoseconds represents a very promising route. Here we present an experimental demonstration of few-ps OPCPA in DKDP, in order to experimentally verify the feasibility of the scheme. Broadband amplification was observed in the wavelength range of 830-1310 nm. The amplified spectrum supports two optical cycle pulses, at a central wavelength of ~920 nm, with a pulse duration of 6.1 fs (FWHM). The comparison of the experimental results with our numerical calculations of the OPCPA process showed good agreement. These findings confirm the reliability of our theoretical modelling, in particular with respect to the design for further amplification stages, scaling the output peak powers to the petawatt scale.

We present the development of a light source for generating optically synchronized seed pulses both for the parametric amplifier chain and the pump-laser chain of the Petawatt Field Synthesizer (PFS), which is currently under construction at MPQ. The PFS system aims at delivering waveform-controlled few-cycle laser pulses with PW-scale peak power using optical parametric chirped pulse amplification (OPCPA). Methods of generating the broadband nearinfrared (NIR) seed pulses for the OPCPA chain by spectral broadening using few-cycle pulses are presented. We also demonstrate the generation of a supercontinuum spanning up to three octaves (270-1500 nm) using cascaded hollowcore fibers which supports sub-cycle pulse duration.

We present a chirped pulse amplification (CPA) system based on diode-pumped Yb:YAG. The stretched ns-pulses are amplified and have been compressed to less than 900 fs with an energy of 200 mJ and a repetition rate of 10 Hz. This system is optically synchronized with a broadband seed laser and therefore ideally suited for pumping optical parametric chirped pulse amplification (OPCPA) stages on a ps-timescale.

In an optically synchronized short-pulse optical-parametric chirped-pulse amplification (OPCPA) system, we observe a few-100 fs-scale timing jitter. With an active timing stabilization system slow fluctuations are removed and the timing jitter can be reduced to 100 fs standard deviation (Std). As the main source for the timing fluctuations we could identify air turbulence in the stretcher-compressor setup inside the chirped pulse amplification (CPA) pump chain. This observation is supported by theoretical investigation of group delay changes for angular deviations occurring between the parallel gratings of a compressor or stretcher, as they can be introduced by air turbulence.

In this paper the development and implementation of a novel amplifier setup as an additional stage for the CPA pump laser of the Petawatt Field Synthesizer, currently developed at the Max‐Planck‐Institute of Quantum Optics, is presented. This amplifier design comprises 20 relay‐imaged passes through the active medium which are arranged in rotational symmetry. As the gain material, an in‐house‐developed Yb:YAG active‐mirror is used. With this setup, stretched 4 ns seed pulses are amplified to output energies exceeding 1 J with repetition rates of up to 2 Hz. Furthermore, a spectral bandwidth of 3.5 nm (FWHM) is maintained during amplification and the compression of the pulses down to their Fourier‐limit of 740 fs is achieved. To the best of our knowledge, this is the first demonstration of 1 TW pulses generated via CPA in diode‐pumped Yb:YAG.