We report on results from the fully diode-pumped chirped-pulse amplification laser system Polaris. Pulses were amplified to a maximum energy of 54.2 J before compression. These pulses have a full width at half-maximum spectral bandwidth of 18 nm centered at 1033 nm and are generated at a repetition rate of 0.02 Hz. To the best of our knowledge, these are the most energetic broadband laser pulses generated by a diode-pumped laser system so far. Due to the limited size of our vacuum compressor, only attenuated pulses could be compressed to a duration of 98 fs containing an energy of 16.7 J, which leads to a peak power of 170 TW. These pulses could be focused to a peak intensity of 1.3×10²¹ W/cm². Having an ultra-high temporal contrast of 10¹² with respect to amplified spontaneous emission these laser pulses are well suited for high-intensity laser-matter experiments.

An analytical model is presented describing the temporal intensity contrast determined by amplified spontaneous emission in high‐intensity laser systems which are based on the principle of chirped pulse amplification. The model describes both the generation and the amplification of the amplified spontaneous emission for each type of laser amplifier. This model is applied to different solid state laser materials which can support the amplification of pulse durations ≤350 fs . The results are compared to intensity and fluence thresholds, e.g. determined by damage thresholds of a certain target material to be used in high‐intensity applications. This allows determining if additional means for contrast improvement, e.g. plasma mirrors, are required for a certain type of laser system and application. Using this model, the requirements for an optimized high‐contrast front‐end design are derived regarding the necessary contrast improvement and the amplified “clean” output energy for a desired focussed peak intensity. Finally, the model is compared to measurements at three different high‐intensity laser systems based on Ti:Sapphire and Yb:glass. These measurements show an excellent agreement with the model.

We report on the first generation of high-contrast, 164 fs duration pulses from the laser system POLARIS reaching focused peak intensities in excess of 2×10(20) W/cm2. To our knowledge, this is the highest peak intensity reported so far that has been achieved with a diode-pumped, solid-state laser. Several passive contrast enhancement techniques have been specially developed and implemented, achieving a relative prepulse intensity smaller than 10(-8) at t=-30 ps before the main pulse. Furthermore a closed-loop adaptive-optics system has been installed. Together with angular chirp compensation, this method has led to a significant reduction of the focal spot size and an increase of the peak intensity.

No abstract

The development, the underlying technology and the current status of the fully diode-pumped solid-state laser system POLARIS is reviewed. Currently, the POLARIS system delivers 4 J energy, 144 fs long laser pulses with an ultra-high temporal contrast of 5×10 12 for the ASE, which is achieved using a so-called double chirped-pulse amplification scheme and cross-polarized wave generation pulse cleaning. By tightly focusing, the peak intensity exceeds 3.5 × 10 20 W cm −2 . These parameters predestine POLARIS as a scientific tool well suited for sophisticated experiments, as exemplified by presenting measurements of accelerated proton energies. Recently, an additional amplifier has been added to the laser chain. In the ramp-up phase, pulses from this amplifier are not yet compressed and have not yet reached the anticipated energy. Nevertheless, an output energy of 16.6 J has been achieved so far.

We present the first complete temporal and spatial characterization of the amplified spontaneous emission (ASE) of laser radiation generated by a diode-pumped high-power laser system. The ASE of the different amplifiers was measured independently from the main pulse and was characterized within a time window of -10ms ≤ t ≤ 10ms and an accuracy of up to 15fs around the main pulse. Furthermore, the focusability and the energy of the ASE from each amplifier was measured after recompression. Using our analysis method, the laser components, which need to be optimized for a further improvement of the laser contrast, can be identified. This will be essential for laser-matter interaction experiments requiring a minimized ASE intensity or fluence.

We report the amplification of laser pulses at a center wavelength of 1034 nm to an energy of 16.6 J from a fully diode-pumped amplifier using Yb:CaF2 as the active medium. Pumped by a total optical power of 300 kW from high-power laser diodes, a gain factor of g=6.1 was achieved in a nine-pass amplifier configuration agreeing with numerical simulations. A measured spectral bandwidth of 10 nm full width at half-maximum promises a bandwidth-limited compression of the pulses down to a duration of 150 fs. These are, to our knowledge, the most energetic laser pulses achieved from a diode-pumped chirped-pulse amplifier so far.

We report on the successful implementation and characterization of a cryogenic solid hydrogen target in experiments on high-power laser-driven proton acceleration. When irradiating a solid hydrogen filament of 10 μm diameter with 10-Terawatt laser pulses of 2.5 J energy, protons with kinetic energies in excess of 20 MeV exhibiting non-thermal features in their spectrum were observed. The protons were emitted into a large solid angle reaching a total conversion efficiency of several percent. Two-dimensional particle-in-cell simulations confirm our results indicating that the spectral modulations are caused by collisionless shocks launched from the surface of the the high-density filament into a low-density corona surrounding the target. The use of solid hydrogen targets may significantly improve the prospects of laser-accelerated proton pulses for future applications.