High-powered electric propulsion thrusters utilizing a magnetized plasma require that plasma exhaust detach from the applied magnetic field in order to produce thrust. This paper presents experimental results demonstrating that a sufficiently energetic and flowing plasma can indeed detach from a magnetic nozzle. Microwave interferometer and probe measurements provide plume density, electron temperature, and ion flux measurements in the nozzle region. Measurements of ion flux show a low-beta plasma plume which follows applied magnetic field lines until the plasma kinetic pressure reaches the magnetic pressure and a high-beta plume expanding ballistically afterward. Several magnetic configurations were tested including a reversed field nozzle configuration. Despite the dramatic change in magnetic field profile, the reversed field configuration yielded little measurable change in plume trajectory, demonstrating the plume is detached. Numerical simulations yield density profiles in agreement with the experimental results.

A technique is presented for measuring small displacements by observing the frequency of spectral modulation of white light in a Michelson interferometer. An experiment is described in which the step size of a stepper-motor-driven translation stage was measured by recording the spectrum of light output from an interferometer and performing a cross-correlation calculation with theoretical spectra. Measurements made using standard laboratory-quality optical equipment were accurate to within ~10 nm for a range of over 100 microm.

High spatial resolution plasma density measurements have been taken as part of an investigation into magnetic nozzle physics at the NASA/MSFC Propulsion Research Center. These measurements utilized a Langmuir triple probe scanned across the measurement chord of either of two stationary rf interferometers. By normalizing the scanned profile to the microwave interferometer line-integrated density measurement for each electrostatic probe measurement, the effect of shot-to-shot variation of the line-integrated density can be removed. In addition, by summing the voltage readings at each radial position in a transverse scan, the line density can be reconstituted, allowing the absolute density to be determined, assuming that the shape of the profile is constant from shot to shot. The spatial and temporal resolutions of this measurement technique depend on the resolutions of the scanned electrostatic probe and the interferometer. The measurement accuracy is 9%-15%, which is on the order of the accuracy of the rf interferometer. The measurement technique was compared directly with both scanning rf interferometer and standard Langmuir probe theory. The hybrid technique compares favorably with the scanning rf interferometer, and appears more accurate than probe theory alone. Additionally, our measurement technique is generally applicable even for nonaxisymmetric plasmas.

A polychromatic microwave quadrature interferometer has been characterized using several laboratory plasmas. Reflections between the transmitter and the receiver have been observed, and the effects of including reflection terms in the data reduction equation have been examined. An error analysis which includes the reflections, modulation of the scene beam amplitude by the plasma, and simultaneous measurements at two frequencies has been applied to the empirical database, and the results are summarized. For reflection amplitudes around 1096, the reflection terms were found to reduce the calculated error bars for electron density measurements by about a factor of 2. The impact of amplitude modulation is also quantified. In the complete analysis, the mean error bar for highdensity measurements is 7.596, and the mean phase shift error for low-density measurements is 1.2".. PACS no.'s/OCIS codes, etc analogue I. Introduction.

Electron density measurements have been made in steady-state plasmas in a spherical inertial electrostatic confinement (IEC) discharge using microwave interferometry. Plasma cores interior to two cathodes, having diameters of 15 and 23 cm, respectively, were probed over a transverse range of 10 cm with a spatial resolution of about 1.4 cm for buffer gas pressures from 0.2 to 6 Pa in argon and deuterium. The transverse profiles are generally flat, in some cases with eccentric symmetric minima, and give mean densities of from ≈0.4 to 7×1010 cm−3, the density generally increasing with the neutral gas pressure. Numerical solutions of the one-dimensional Poisson equation for IEC plasmas are reviewed and energy distribution functions are identified which give flat transverse profiles. These functions are used with the plasma approximation to obtain solutions which also give densities consistent with the measurements, and a double potential well solution is obtained which has minima qualitatively similar to those observed. Explicit consideration is given to the compatibility of the solutions interior and exterior to the cathode, and to grid transparency. Deuterium fusion neutron emission rates were also measured and found to be isotropic, to within the measurement error, over two simultaneous directions. Anisotropy was observed in residual emissions during operation with nonfusing hydrogen-1. The deuterium rates are consistent with predictions from the model. 2004 American Institute of Physics.

No abstract

No abstract

No abstract