Over the present material synthesis routes, the sonochemical route is highly efficient and comfortable way to produce nanostructured materials. In this way, the copper sulfide (CuS-covellite) and sulfur doped reduced graphene oxide (S-rGO) nanocomposite was prepared by sonochemical method. Interestingly, the structure of the as-prepared S-rGO/CuS was changed from the covellite to digenite phase. Herein, the S-rGO was act as a mild oxidizer and liable for the structural transformations. These structural changes are sequentially studied by various physicochemical characterizations such as Fourier transform infrared spectroscopy (FT-IR), Raman spectroscopy, X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS) and Transmission electron microscopy (TEM). After scrupulous structural evaluations, the transformation of CuS phase was identified and documented. This oxidized CuS has an excellent electrocatalytic activity when compare to the bulk CuS. This S-rGO/CuS was further used for the determination of glucose and acquired good electrocatalytic performances. This S-rGO/CuS was exhibited a wide linear concentration range, 0.0001–3.88 mM and 3.88–20.17 mM, and a low-level detection limit of 32 nM. Moreover, we have validated the practicability of our developed glucose sensor in real biological samples.

No abstract

In the present work, potato-like silver molybdate (Ag2MoO4) microstructures were synthesized through a simple hydrothermal method. The microstructures of Ag2MoO4 were characterized by various analytical and spectroscopic techniques such as XRD, FTIR, Raman, SEM, EDX and XPS. Interestingly, the as-prepared Ag2MoO4 showed excellent photocatalytic and electrocatalytic activity for the degradation of ciprofloxacin (CIP) and electrochemical detection of hydrogen peroxide (H2O2), respectively. The ultraviolet-visible (UV-Vis) spectroscopy results revealed that the potato-like Ag2MoO4 microstructures could offer a high photocatalytic activity towards the degradation of CIP under UV-light illumination, leads to rapid degradation within 40 min with a degradation rate of above 98%. In addition, the cyclic voltammetry (CV) and amperometry studies were realized that the electrochemical performance of Ag2MoO4 modified electrode toward H2O2 detection. Our H2O2 sensor shows a wide linear range and lower detection limit of 0.04–240 μM and 0.03 μM, respectively. The Ag2MoO4 modified electrode exhibits a high selectivity towards the detection of H2O2 in the presence of different biological interferences. These results suggested that the development of potato-like Ag2MoO4 microstructure could be an efficient photocatalyst as well as electrocatalyst in the potential application of environmental, biomedical and pharmaceutical samples.

In this present work, "killing two birds with one stone" strategy was performed for the electrochemical trace level detection and photocatalytic degradation of antibiotic drug chloramphenicol (CAP) using Ce(MoO) nanocubes/graphene oxide (CeM/GO) composite for the first time. The CeM/GO composite was synthesized via simple hydrothermal treatment followed by sonication process. The successful formation of CeM/GO composite was confirmed by several analytical and spectroscopic techniques. The CeM/GO composite modified glassy carbon electrode (GCE) showed excellent electrocatalytic activity toward the reduction of CAP in terms of decrease the potential and increase the cathodic peak current in comparison with different modified and unmodified electrodes. The electrocatalytic reduction of CAP based on the CeM/GO modified GCE exhibited high selectivity, wide linear ranges, lower detection limit, and good sensitivity of 0.012-20 and 26-272 μM, 2 nM ,and 1.8085 μA μM cm, respectively. Besides, when CeM/GO/GCE was used to analyze the CAP in real samples, such as honey and milk, the satisfactory recovery results were obtained. On the other hand, the CeM/GO composite played excellent catalyst toward the photodegradation of CAP. The obtained results from the UV-vis spectroscopy clearly suggested that CeM/GO composite had high photocatalytic activity compared to pristine Ce(MoO4) nanocubes. The degradation efficiency of CeM/GO toward CAP is observed about 99% within 50 min under visible irradiation and it shows a good stability by observing the reusability of the catalyst. The enhanced photocatalytic performance was attributed to the increased migration efficiency of photoinduced electrons and holes.

No abstract

Followed by decades of successful efforts in developing cathode materials for high specific capacity lithium-ion batteries, currently the attention is on developing a high-voltage battery (>5 V vs Li/Li+) with an aim to increase the energy density for their many fold advantages over conventional <4 V batteries. Among the various cathode materials, phosphate polyanion materials (LiMPO4, where M is a single metal or a combination of metals) showed promising candidacy given their high electrochemical potential (4.8–5 V vs Li/Li+), long cycle stability, low cost, and achieved specific capacity (∼165 mAh·g–1) near to its theoretical limit (170 mAh·g–1). In this review, factors affecting the electrochemical potential of the cathode materials are reviewed and discussed. Techniques to improve the electrical and ionic conductivities of phosphate polyanion cathodes, namely, surface coating, particle size reduction, doping, and morphology engineering, are also discussed. A processing–property correlation in phosphate polyanion materials is also undertaken to understand relative merits and drawbacks of diverse processing techniques to deliver a material with targeted functionality. Strategies required for high-voltage phosphate polyanion cathode materials are envisioned, which are expected to deliver lithium-ion battery cathodes with higher working potential and gravimetric specific capacity.

As a growing aspect of materials science, there are an enormous number of synthesis routes that have been identified to produce materials, particularly through simple methodologies. In this way, the present study focuses on the easiest way to prepare sulfur doped carbon nanoparticles (SDCNs) using a flame synthesis method and has also demonstrated a novel route to synthesize Ni(OH)2 decorated SDCNs by a simple adsorption cum precipitation method. The SDCNs are alternative candidates to prestigious carbon materials such as graphene, carbon nanotubes, and fullerenes. Moreover, SDCNs provide excellent support to the Ni(2+) ion adsorption and initiate the formation of Ni(OH)2. The formation of Ni(OH)2 on the SDCN matrix was confirmed by Fourier transform infrared spectroscopy (FT-IR), Raman spectroscopy, X-ray diffraction (XRD), selected area diffraction pattern (SAED), X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM), and transmission electron microscopy (TEM). After these meticulous structural evaluations, we have described the mechanism for the formation of Ni(OH)2 on an SDCN matrix. The as-prepared Ni(OH)2 decorated SDCN nanocomposites were used as an electrode material for nonenzymatic glucose sensors. The fabricated glucose sensor exhibited a wide linear concentration range, 0.0001-5.22 mM and 5.22-10.22 mM, and a low-level detection limit of 28 nM. Additionally, it reveals excellent selectivity in the potentially interfering ions and also possesses a good stability. The practicality of the fabricated glucose sensor was also demonstrated toward glucose detection in biological samples.

No abstract