A preocupação global com o alto consumo de energia e o consequente aumento da poluição vêm levando o meio acadêmico a pesquisar materiais de origens naturais que possam substituir produtos utilizados na indústria e construção civil. Um dos materiais que pode ser utilizado como substituto na produção de vários produtos e que já vem sendo empregado na construção civil, arquitetura e no design é o bambu e suas fibras, este material é considerado leve, resistente, versátil, com adequadas características físicas e mecânicas. Diante disso o objetivo deste trabalho é realizar uma revisão literária para apresentar como ocorrem a aplicação e tratamentos aplicados as fibras naturais, especificamente a de bambu, para fins industriais. Inicialmente é realizada uma apresentação sobre as características botânicas da planta e posteriormente os tratamentos aplicados para melhorar suas propriedades. Por fim são apresentadas algumas das possibilidades de aplicação das fibras em materiais compósitos e na construção civil. Os resultados mostram algumas possibilidades para tratamento e as principais aplicações para as fibras naturais, com isso esperasse destacar que a utilização de fibras naturais especificamente à fibra de bambu pode ser, e vem sendo utilizada como alternativa viável para suprir as necessidades de determinados materiais.
A indústria têxtil tem buscado fortemente se manter competitiva no mercado, sendo que um dos seus maiores desafios é a busca pela eficiência na produtividade. Diante disso, o desenvolvimento de um Layout otimizado pode contribuir para a melhoria das atividades das organizações, gerando benefícios para a competitividade. Com isso, o objetivo deste trabalho é desenvolver a metodologia SLP - Systematic Layout Planning para buscar um novo Layout para uma indústria da área têxtil, alinhando a eficiência produtiva aos conceitos de qualidade nos produtos acabados. A metodologia adotada no desenvolvimento deste estudo manteve uma abordagem qualitativa. Já a coleta de dados foi realizada por meio de entrevistas e questionários. Como resultado, constatou-se a importância de se analisar os modelos de layouts produtivos, visto que os resultados atingidos foram de extrema importância para a concordância do trabalho com os objetivos gerais da empresa. Os resultados apresentam as características do novo Layout que foi projetado, de modo a utilizar o espaço disponível, onde foi possível manter os corredores dentro do estabelecido pela norma, além de projetar os maquinários e postos de trabalho de modo a promover um fluxo mais objetivo e eficiente, reduzindo, assim, a movimentação desnecessária de materiais e pessoas.
The assembly process in companies is something that must be analyzed from the design of their products until assembly, because this directly affects the product cost, assembly time, shape or quality in the process. An important tool for these activities is the standardized work that went well for the assembly line of the companies can be a good alternative to contribute to improve the assembly process. The purpose of this study is to standardize the assembly process of a group of components to converting and packaging tissue. The research methodology applied in this study is bibliographic followed by action research, with practical application in a case study. Initially the company is presented and followed by a current assembly process identification. Subsequently the problems are identified and the development and application of the improvement tools for the standardization of the assembly process in a pilot group of components. Finally, the results are presented and can be observed that the development of the standardized work process reduced the receiving, warehousing and assembly parts, as well as a reduction of 7% in the internal assembly cost, which represents a saving in the annual purchases of $ 46,400.
Cemented carbides (WC-Co) are difficult to be processed by conventional machining processes. Electrical discharge machining (EDM) appears as an efficient technology to manufacture WC-Co products with high accuracy. In EDM literature no research works investigating the influences of different grades of CuW electrodes on geometrical characteristics when ED-machining the same cemented carbide was found. This work presents an investigation on ED-Machining of cemented carbide (WC-Co) with 10% Co using two grades of coper-tungsten (CuW) electrodes with 65% and 85% of tungsten. ED-Machining experiments were carried out under rough, semifinish and finish regimes with input variables discharge current i e , discharge duration t e and pulse interval time t o using analysis of variance (ANOVA) based on design of experiments with complete factorial 3 2. Output variables evaluated were WC-Co workpiece geometrical characteristics 3D surface roughness and round cavities circularity measures. Results showed that ED-Machining regime is the most significant parameter on both WC-Co workpiece circularity and surface roughness measures. Electrodes grades CuW65 and CuW85 presented similar results on workpiece circularity and 3D surface roughness.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.