This study was made to determine surface characteristics such as colour, gloss, and surface hardness changes of Oriental beech (Fagus orientalis). The wood specimens were firstly impregnated with some fireretardants (FRs) and primed with epoxy resin (EPR) and then coated with polyurethane/polyurea hybrid resin (PUU). Oriental beech was impregnated with 3 % aqueous solution of boric acid (BA), borax (BX), boric acid and borax mixture (1:1), and ammonium sulphate (AS). While Sikafloor®-156 was used for epoxy coating (EPR), Sikalastic®-851 R was used for polyurethane/polyurea hybrid coating (PUU). According to our results, all treatment groups gave negative lightness stability values after accelerated weathering. The colour stability of epoxy resin coated Oriental beech was higher than that of polyurethane/polyurea hybrid resin coated Oriental beech. Except for boric acid impregnated and polyurethane/polyurea hybrid resin coated Oriental beech, all fire-retardants treatment before polyurethane/polyurea hybrid resin and epoxy resin coatings decreased the gloss losses of Oriental beech after accelerated weathering. Fire-retardants impregnation before epoxy resin and polyurethane/polyurea hybrid resin coatings improved the surface hardness values of Oriental beech after accelerated weathering.

This study aimed to determine the effect of accelerated weathering on gloss, surface hardness and colour changes of Scots pine (Pinus sylvestris L.). Test samples were impregnated with Adolit KD‐5, Wolmanit CX‐8 and Celcure AC‐500 covered with cellulosic and polyurethane varnishes. The results showed that the values of surface hardness and gloss increased after accelerated weathering. While the surface hardness of Scots pine was increased for impregnated and polyurethane‐coated varnish, it decreased for impregnated and cellulosic varnish‐coated Scots pine after 1000 hours of accelerated weathering exposure. Copper‐based chemical impregnation and varnish coating developed the gloss of Scots pine specimens relative to the surface characteristics observed in single‐coated Scots pine specimens. While the most appropriate chemical was Celcure AC‐500 for surface hardness, it was Adolit KD‐5 for the gloss of Scots pine after 1000 hours of accelerated weathering exposure. Wood specimens impregnated prior to the application of varnish were more effective in stabilising the colour of Scots pine than Scots pine only coated with varnish. Polyurethane varnish‐treated Scots pine showed better colour stability for each partial and total accelerated weathering exposure period. The total colour changes were lowest for polyurethane varnish‐coated Scots pine impregnated with Celcure AC‐500 after 1000 hours of accelerated weathering exposure.

In this study, it was aimed to investigate the effects of weathering on some surface characteristics such as color and surface roughness changes of Scots pine impregnated with copper-containing chemical such as Wolmanit CX-8 (WCX-8) and varnished with synthetic varnish (SV), cellulosic varnish (CV), and polyurethane varnish (PV) were investigated. Results showed that while the WCX-8 impregnated and PV coated Scots pine specimens showed better color stability than other treatment groups after weathering, only CV coated Scots pine gave the most negative effect on color stability. While, the untreated (control) wood surface turned from red to green and yellow to blue respectively, after weathering, other all treatment groups gave reddish and yellowish tone after weathering. Weathering conditions increased the surface roughness of control (untreated) and other all treatment groups. The control group gave a rougher surface than other treatment groups after weathering. Surface roughness increases were the lower for CV coated Scots pine wood than other treatment groups. The results showed that while WCX-8 impregnation before varnishing gave better color characteristics, generally it caused to increase the surface roughness of Scots pine after weathering.

Weathering performance of impregnated and coated wood products is an important issue that influences their appearance as well as their service life after outdoor or indoor exposure. A novel procedure to improve the weathering performance of Scots pine wood (Pinus sylvestris L.) is proposed in this study. Wood samples were impregnated with ammonium tetrafluoroborate (ATFB), ammonium pentaborate (APB) and boric acid (BA), and afterward coated with a layer of liquid glass (LG). Surface hardness, color changes, and surface roughness of wood samples were investigated after 250 h and 500 h of exposure to artificial weathering. The results revealed that, except for untreated (control), all other treatment groups caused an increase in surface hardness of Scots pine after weathering. A decrease in the CIE L* value corresponds to the darkening of samples after weathering. Borates-impregnated and LG-coated Scots pine samples possessed the highest color stability. However, all treatment combinations resulted in reddish and yellowish tones after weathering. Exposure to weathering increased surface roughness of wood samples. The surface roughness of the untreated (control) group was higher than that of impregnated and coated samples.

This study was designed to investigate the weathering characteristics of Calabrian pine (Pinus brutia) wood. The wood specimens were impregnated with some copper-based chemicals and then varnish coated. As copper-based chemicals, Celcure C4, Korasit KS, and Tanalith E 8000 were used for impregnation. Polyurethane varnish (PV) and water-based varnish (WBV) were used as coating materials. Firstly, Calabrian pine wood was impregnated with 2,5 % and 5 % aqueous solutions of chemicals then coated with PV and WBV. Impregnated and coated Calabrian pine wood specimens were subjected to 6 months of natural weathering in Muğla, Turkey. After weathering, surface hardness, surface roughness, and adhesion strength changes of Calabrian pine wood specimens were determined. Impregnation caused to increase in surface hardness values of Calabrian pine. Surface hardness increases of WBV coated Calabrian pine specimens were higher than that of PV coated Calabrian pine specimens. Impregnation resulted in higher surface roughness values of Calabrian pine specimens. PV coated Calabrian pine specimens gave higher surface roughness than that of WBV coated Calabrian pine specimens. The adhesion strength values of all treatment groups were decreased after

No abstract

The study aimed to determine some surface parameters such as surface roughness and color changes of thermally modified Oriental beech (Fagus orientalis L.) wood samples after 750 hours of artificial weathering. The results of the study showed that artificial weathering led to an increase in surface roughness of Oriental beech wood. Thermal modification interval of 210 °C - 230 °C gave a smoother surface than unmodified samples after artificial weathering. Artificial weathering caused darker, reddish, and yellowish tone of unmodified and thermally modified Oriental beech wood. According to the study fi ndings, surface properties of thermally modified Oriental beech wood were better than those of unmodified Oriental beech.

This study was designed to investigate physical properties such as color changes after weathering and water absorption (WA) levels, and combustion performance of borates-impregnated and LG-coated Oriental beech wood. Results showed that borates impregnated and LG-coated Oriental beech wood showed positive lightness stability after weathering. The best color stabilization was obtained with LG-coated Oriental beech. Except for the 1 h WA period, LG did not show a water repellent effect after the water absorption test. Borates impregnation before LG-coating caused to decrease in weight loss of Oriental beech after the combustion test. Moreover, the lowest weight losses were obtained in borate impregnated Oriental beech wood.