Incineration bottom ash is generated by the incineration of solid waste. Household solid waste is increasing every year and so is incineration bottom ash. This is a problem to treat the incineration bottom ash because the ash has many toxic components. Cement composites can solve this problem and there are many studies for using the bottom ash as fine aggregate. To evaluate the usage of incineration bottom ash, compressive strength, mercury intrusion porosimetry, scanning electron microscopy-backscatter electron, X-ray diffraction, and toxicity characteristic leaching processes were performed. When using incineration bottom ash up to 20% of substitution, the compressive strength in all cases was increased. This study showed how the filler effect appeared well in the cement composites through the scanning electron microscopy-backscatter electron, and mercury intrusion porosimetry. X-ray diffraction indicated the possibility of an alkali-silica reaction of the aggregate with the components of incineration bottom ash. This problem is an obstacle to applying the incineration bottom ash as a fine aggregate. In addition, the toxicity characteristic leaching process was shown to be under the threshold of the Korean standard, however, this should nuanced by the consideration of amorphity. Comprehensively, incineration bottom ash could be used as a fine aggregate of up to 20% of substitution. However, the pre-treatment would need to eliminate or reduce alkali reactive components and heavy metals.
The purpose of this study was to prevent early age autogenous shrinkage in high-strength mortars with saturated tea waste particles. In general, high strength and high performance concretes are made with low water/binder ratios; hence, they are susceptible to shrink at early ages. This shrinkage occurs due to self-desiccation that leads to autogenous shrinkage. To overcome self-desiccation problems in high-strength cement composites, it is necessary to keep the composites moist for a long time. Pre-saturated porous lightweight aggregates and super absorbent polymers are the most commonly used materials in high-strength cement composites to keep them moist for a long time; however, in this study, porous tea waste particles were used to keep the cement mortars moist. Pre-saturated tea waste particles were used in two different size proportions, making up as much as 3% of the volume of the binder. Moreover, commonly used lightweight aggregate (perlite) was also used to compare the outcomes of specimens made with tea waste particles. Different parameters were observed, such as, flow of fresh mortars, autogenous shrinkage, mechanical strengths and microstructure of specimens. The addition of tea waste and perlite particles in mortars made with Ordinary Portland cement (OPC) as the only binder, showed a reduction in flow, autogenous shrinkage and mechanical strengths, as compared to mixes made with partial addition of silica fume. Although, the use of silica fume improved the mechanical strength of specimens. Moreover, the use of saturated tea waste and perlite particles also improved the microstructure of specimens at an age of 28 days. The results revealed that the saturated tea waste particles have the ability to prevent autogenous shrinkage but they reduce strength of high-strength mortars at early ages.
To solve the problem of black ice, many studies are being carried out. The key in recent days is enhancing the thermal conductivity of concrete. In this study, to improve the thermal conductivity, silicon carbide was used to substitute 50% and 100% of the fine aggregate. In addition, steel fiber is not only for enhancing the mechanical properties but could enhance thermal conductive material. Hence, the arched-type steel fiber was used up to a 1% volume fraction in this study. Furthermore, graphite was used for 5% of the volume fraction for enhancing the thermal conductivity. However, thermal damage would occur due to the difference in thermal conductivity between materials. Therefore, the thermal durability must be verified first. The target application of the concrete in this study was its use as road paving material. To evaluate the thermal durability, freeze–thaw and rapid cyclic thermal attacks were performed. The thermal conductivity of the specimens was increased with the increase in thermal conductive materials. Graphite has already been reported to have a negative effect on mechanical properties, and the results showed that this was the case. However, the steel fiber compensated for the negative effect of graphite, and the silicon carbide provided a filler effect. Graphite also had a negative effect on the freeze–thaw and rapid cyclic thermal attack, but the steel fiber compensated for the reduction in thermal durability. The silicon carbide also helped to improve the thermal durability in the same way as steel fiber. Comprehensively, the steel fiber enhanced all of the properties of the tests. Using 100% silicon carbide was considered the acceptable range, but 50% of silicon carbide was the best. Graphite decreased all the properties except for the thermal conductivity. Therefore, the content of graphite or using other conductive materials used should be carefully considered in further studies.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.