No abstract

No abstract

Recent progress in research on the cutting processes of wood is presented, particularly in regard to new methods of accomplishing an increase in volume recovery by sawmills. The suitability of modern fracture mechanics was demonstrated for the estimation of the cutting power for saws in which kerfs are different from saws used in cutting tests, and whereby the data of sawn material – such as the specific work of surface formation (toughness) and the shear yield stress – were determined. Cutting tests were carried out on the modern frame sawing machine (sash gang saw) for narrow-kerf sawing with the hybrid dynamically balanced driving system and elliptical teeth trajectory movement.

The measurement of cutting forces permits building of physic-mechanical cutting models for a better understanding of the phenomena observed during cutting. It also permits the design and optimization of processes, machines, tools, and wood preparation. Optimization of cutting conditions of wood-based materials can decrease the cutting forces, which directly relates to the energy consumption and surface quality. The sawdust analysis may serve for analysis of cutting kinematics and occupational health risk. The aim of the study was to estimate the correlation between the feed rate and both feed force and sawdust particle size produced during particleboard circular sawing. A saw machine type K700 was used in experiments. There were three feed rates of 12, 18, and 24 m/min executed by a horizontal pneumatic actuator fixed to the sliding side table of the saw machine. Based on the results of the experiments, a positive correlation was observed between the feed rate in a circular sawing process and feed forces and an unexpected particle size distribution depending on the feed rate.

Air pollution by wood dust in furniture production sites is an important hygiene issue. The dust is created by all types of wood and wood-based material machining, and its concentration in the working zone surrounding the machining stand depends on the effectiveness of the dust exhaust system. In present research, three setups of the dust extraction system for a conventional table sawing machine are considered while machining particleboards. The results showed a high impact of the exhaust system connection setup on the dust concentration in the air surrounding the sawing machine work stand. The use of both main and auxiliary sawdust extraction connectors together ensured the highest clearness of the air, with only 0.5 mg/m3 of dust concentration. Closing the upper hood leads to a concentration five times higher, while disconnecting it results in a ten times higher dust content. The finest dust particles (<1 µm), however, are the most numerous in the case of closing the hood.

An analysis of forces acting in the peripheral up-milling of particleboard is presented. First, a novel method of high-frequency piezoelectric force signal treatment is proposed and used to separate the original force signal from the vibrations of the previous cutting iteration. This allows for the analysis of single chip cutting force courses during industrial CNC (Computer Numerical Control) milling. The acting forces are compared with the theoretical, instantaneous, uncut chip thickness. The results show that, for a range of 40–60 m/s, the higher the cutting speed used, the higher the resultant and principal cutting forces. The method of cutting thrust force used was similar to that observed in solid wood milling, i.e., first using a pushing action, followed by a pulling action. The obtained average specific principal cutting forces for particleboard peripheral up-milling are equal to 32.0 N/mm2 for slow and 37.6 N/mm2 for fast milling. The specific cutting thrust force decreases with the increase in instantaneous uncut chip thickness.

This paper presents an approach to the design of an upholstered furniture frame using the finite element method and empirical studies. Three-dimensional discrete models of upholstered furniture frames were developed taking into account orthotropic properties of solid pine wood (Pinus sylvestris L.) without and with details strengthening their structure in the form of glue joints and upholstery staples. Using the CAE Autodesk Inventor Nastran finite element method, linear static analyses were performed by simulating normative loading. The finite element method was performed considering the experimentally determined stiffness coefficients of the PCAC adhesive and staple joints. As a result, stress, displacement, and equivalent strain distributions were obtained for upholstered furniture frame models with stapled corner joints. The deformation and strength behavior of the upholstered furniture frames was improved by reinforcing with a wood strip. A new approach to the design of upholstered furniture frame frames using the FEM method with stapled component connections was developed and tested. The results of the study can be applied in the optimization of upholstered furniture construction.

• A very useful method was successfully applied in the investigation of tools for machining wood and