Gas Turbine Engines operate at temperatures higher than current material temperature limits. This necessitates cooling the metal through internal or external means and/ or protecting the metal with coatings that have higher material limits. Film cooling is one of the major technologies allowing today’s gas turbines to operate at extremely high turbine inlet temperatures, consequently higher power density, and extend the cooled components life. Film cooling is a technique where a coolant is blown over the surface exposed to hot gas and a film of low temperature gas is maintained that protects the metal surface from the hot gas. The application of effective film-cooling techniques provides the first and best line of defense for hot gas path surfaces against the onslaught of extreme heat fluxes, serving to directly reduce the incident convective heat flux on the surface. The effectiveness of film cooling methods depends on the blowing ratio, shape of the cooling holes, and geometrical parameters such as the area ratio and diffusion angle. Film cooling is performed almost exclusively through the use of discrete holes. The holes can be of round or other shaped. A detailed study of the literature shows that the fan shaped has higher effectiveness when compared to other shapes. In this study a number of cooling hole shapes are evaluated numerically using the Computational Fluid Dynamics (CFD) tool ANSYS-CFX-11.0 with the objective of improving cooling effectiveness under a favorable pressure gradient main flow. In order to delineate the effects of shape from that of diffusion, a constant area ratio is assumed first. In the next set of analyses the effect of hole exit diffusion is considered. Results are presented in terms of surface temperatures and adiabatic effectiveness at three different blowing ratios for the different film cooling hole shapes analyzed. Comparison is made with reference to the fan shaped film cooling hole with forward and lateral angles of 10/10/10 degree respectively. Hole shapes that show improvement over the fan shaped hole are identified and optimized.

The performance of the compressor blade is considerably influenced by secondary flow effects, like the cross flow on the end wall as well as corner flow separation between the wall and the blade. The present work is focused on the studying the effects of Vortex Generator (VG) on NASA Rotor 37 test case using Computational Fluid Dynamics (CFD). VG helps in controlling the inception of the stall by generating vortices and energizes the low momentum boundary layer flow which enhances the rotor performance. Three design configuration namely, Counter-rotating, Co-rotating and Plow configuration VG are selected based on the improved aerodynamic performance discussed in reference [1]. These VG are located at 90% span and 42% chord on suction side surface of the blade. Among the three configurations, the first configuration has greater impact on the end wall cross flow and flow deflection which resulted in enhanced numerical stall margin of 5.4% from baseline. The reasons for this numerical stall margin improvement are discussed in detail.

Purpose The purpose of this paper is to study the flow and heat transfer characteristics of microchannel heatsinks with ribs, cavities and secondary channels. The influence of length and width of the ribs on heat transfer enhancement, secondary flows, flow distribution and temperature distribution are examined at different Reynolds numbers. The effectiveness of each heatsink is evaluated using the performance factor. Design/methodology/approach A three-dimensional solid-fluid conjugate heat transfer numerical model is used to study the flow and heat transfer characteristics in microchannels. One symmetrical channel is adopted for the simulation to reduce the computational cost and time. Flow inside the channels is assumed to be single-phase and laminar. The governing equations are solved using finite volume method. Findings The numerical results are analyzed in terms of average Nusselt number ratio, average base temperature, friction factor ratio, pressure variation inside the channel, temperature distribution, velocity distribution inside the channel, mass flow rate distribution inside the secondary channels and performance factor of each microchannels. Results indicate that impact of rib width is higher in enhancing the heat transfer when compared with its length but with a penalty on the pressure drop. The combined effects of secondary channels, ribs and cavities helps to lower the temperature of the microchannel heat sink and enhances the heat transfer rate. Practical implications The fabrication of microchannels are complex, but recent advancements in the additive manufacturing techniques makes the fabrication of the design considered in this numerical study feasible. Originality/value The proposed microchannel heatsink can be used in practical applications to reduce the thermal resistance, and it augments the heat transfer rate when compared with the baseline design.

The effect of impingement cooling on the internal surface (cooling passage) of the leading edge region in a commercial turbine high pressure first stage rotor blade is investigated using Computational Fluid Dynamics (CFD) simulations. The flow domain is obtained by stretching the middle cross section (50% span) of the above mentioned blade. The simulations are performed for 3 different profiles in the cooling flow passage. In all the cases, the nozzle position and Mach number of cooling fluid is kept constant at E/D = 4.32 and 0.4 respectively. In the first case, the suction side profile is modified to facilitate shift in the vortex. This may reduce the crossflow effect, which will enhance the Nuavg. However, simulation results showed that Nuavg is reduced by 2% when compared to base case. In the second case, the coolant flow passage is smoothened at the apex to reduce dead zone and to enhance spreading of the jet. In this case, a 3% increase in Nuavg is obtained. Based on the analysis of velocity contours in the second case, the coolant flow passage in the third case is further modified to improve the spreading of flow. This resulted in 5% increase in the Nuavg when compared to base case.

The performance of axial flow compressor stage can be improved by minimizing the effects of secondary flow and by avoiding flow separation. At higher blade loading, interaction of tip secondary flow and separated flow on blade surface is more near the tip of the rotor. This results in stall and hence decreases compressor performance. A previous study [1] was carried out to improve the performance of a rotating row of blades with the help of Vortex Generators (VGs) and considerable effects were observed. The current investigation is carried out to find out the effect of Vortex Generator (VG) on the performance of a compressor stage. NASA Rotor 37 with NASA Stator 37 (stage) is used as a test case for the current numerical investigation. VGs are placed at different chord wise as well as span wise locations. A mesh sensitivity study has been done so that simulation result is mesh independent. The results of numerical simulation with different geometrical forms and locations of VGs are presented in this paper. The investigation includes a description of the secondary flow effect and separation zone in compressor stage based on numerical as well as experimental results of NASA Rotor 37 with Stator 37 (without VG). It is also observed that the shape and location of the VG impacts the end wall cross flow and flow deflection [1], which result in enhanced stall range.