The purpose of this study was to assess the efficacy of the XP-endo Finisher (FKG Dentaire SA, La Chaux-de-Fonds, Switzerland) file on debris and smear layer removal in curved root canals in comparison to different irrigation regimens. Seventy-five freshly extracted human mandibular molar teeth with mesial root curved more than 20° were used in this study. The mesial root canals were mechanically prepared using the BT-Race rotary system (FKG Dentaire) and divided into five groups (n = 15) according to the following irrigation techniques: positive control, non-agitated, File agitation, XP-endo Finisher, and EndoActivator (Dentsply Tulsa Dental Specialities, Tulsa, OK, USA). Root canals were split longitudinally and evaluated by scanning electron microscopy. Five-grade scoring system was used to assess the presence of debris and smear layer at the coronal, middle, and apical regions. The XP-endo Finisher and EndoActivator groups revealed significantly lower debris and smear layer scores than the other groups at the coronal, middle, and apical regions (P < 0.05). There was no significant difference between XP-endo Finisher and EndoActivator groups (P > 0.05). The apical region had higher debris and smear layer scores compared with the coronal regions in all groups (P < 0.05), except for the positive control group; there was no significant difference between the three regions of the root canal (P > 0.05). Irrigation of curved root canals using XP-endo Finisher and EndoActivator methods appears to be more effective on debris and smear layer removal than the other tested groups.

Background: The purpose of this study was to compare the cyclic fatigue resistance of newly developed TruNatomy instruments (TRN) in single and double (S-shaped) curvature canals with HyFlex CM (HCM), Vortex Blue (VB) and RaCe (RC) instruments. Methods: Size 20/.04 taper and size 25/0.04 of HCM, VB and RC were used. For TRN instruments, size 20/.04 taper (small) and size 26/.04 taper (prime) were used. The instruments were tested in artificial canals with double curvature (coronal curve; 60°curvature, 5 mm radius and apical curve; 70°curvature and 2 mm radius) and single curvature (60°curvature, 5 mm radius). The number of cycles to failure (NCF) was recorded. Data were statistically analyzed by Kruskal-Wallis and Dunn's multiple comparison tests. Weibull analysis was performed on NCF data. Statistical significant was set at p < 0.05. Results: TRN and HCM revealed higher NCF compared with the other instruments for both tested sizes in single and double curvature canals (p < 0.05). TRN and HCM showed no statistically significant difference in the NCF (p > 0.05). The probability of survival was higher for HCM and TRN instruments than VB and RC instruments. Conclusions: HCM and TRN instruments were more resistant to cyclic fatigue than VB and RC instruments in single and double curvature canals. HCM and TRN instruments were anticipated to survive with higher number of cycles than the other tested instruments. RC instrument had the lowest fatigue resistance than the other instruments.

Objectives:To investigate the preferences of general dental practitioners (GDPs) and endodontists in using endodontic intra-canal medications (ICMs).Methods:This observational and descriptive study was conducted in 2014 in the western province of Saudi Arabia. Following ethical clearance and 2 pilot studies, a web-based questionnaire was electronically sent to 375 randomly and systematically selected GDPs and all endodontists in the western province (n=49). An accompanying e-mail explained the study’s aims and confirmed that the data yielded would remain confidential. The responses were collected, and the data was analyzed using the Chi-square test at p=0.05.Results:Significantly, the highest proportion of respondents (53.7%) reported disinfection of the root canals as the main function of ICMs. Calcium hydroxide (CH) was the preferred material of the majority of those who used the same ICM in all cases (85.7%). While the vast majority of all endodontists (87.5%) used CH after pulp extirpation, 48.5% of GDPs used formocresol (p<0.001). Almost 30% of those who used ICMs after pulp extirpation did not do so after cleaning and shaping of vital cases. Most endodontists used CH (62.5%) and antibiotics (37.5%) in necrotic pulp cases without apical lesions, which were significantly greater than those of GDPs who did the same (43.8% and 17.2%).Conclusions:Participants were aware that the main function of ICMs is disinfection of the root canal system. However, it is clear that GDPs should reduce their reliance on phenol- and formaldehyde-based medications. There was a distinct trend toward the use of ICMs, especially CH, in necrotic pulp cases.

The objective of root canal obturation is to achieve a fluid-tight seal. Recently, GuttaFlow bioseal (GB), a root canal sealer composed of polydimethylsiloxane, gutta-percha particles, and bioactive glass ceramics, has been developed, to enhance the sealing ability of root canal filling material. The objective of this study was to assess the sealing ability of GB using a subnanoliter-scaled fluid-flow measuring device and to compare with that of AH Plus (AH). The fluid flow in root canal-filled teeth using either gutta-percha cone (GP) with AH (GAR; n = 10) or GP with GB (GBR; n = 10) and in GP inserted in AH blocks (GA; n = 10) or GP inserted in GB blocks (GB; n = 10) was measured. In addition, fluid flow in sealer blocks of AH (A; n = 10) and GB (B; n = 10), which served as negative controls, was measured. Root canal-filled teeth using GP without any sealer (GR) acted as positive controls (n = 10). The leakage was obtained by calculating the volume of moved water by time (s), after stabilization of the fluid flow was achieved. Statistical analysis was performed using the Kruskal–Wallis test and Mann–Whitney U-test with Bonferroni correction. A p value less than 0.00238 (0.05/21) was considered significantly different. The mean leakages (nL/s) in the groups are as follows: GAR, 0.0958 ± 0.0543; GBR, 0.0223 ± 0.0246; GA, 0.0644 ± 0.0803; GB, 0.0267 ± 0.0182; A, 0.0055 ± 0.0057; B, 0.0052 ± 0.005; and GR, 0.2892 ± 0.3018. The mean leakage in the GBR group was lower than that in the GAR group (p = 0.001), while the mean leakages in the GA and GB groups were not significantly different. GuttaFlow bioseal can be useful in single-cone obturation technique.

Aim: To evaluate the mechanical behavior of reciprocating endodontic files, comparing nickeltitanium (NiTi) and stainless steel 316L (St.St. 316L) as manufacturing material for such instruments. Methods: A three-dimensional finite element model was designed for this study. The simplified instrument model geometry was created on commercial CAD/CAM software. Real strain stress curves of St.St. 316L and NiTi were used in the analysis. Non-linear static analysis was performed to simulate the instrument inside root canal at an angle of 45° in the apical portion, and subjected to torsion of 0.3 N.cm. Results: Non-linear NiTi material showed super elasticity and high functionality in such applications. Very high levels of stress appeared in the file at 3 mm from the tip close to yield point. Conclusions: St. St. 316L is not suitable for manufacturing reciprocating instruments. Modeling of the instrument with equivalent circular cross-sectional area did not affect results quality. Reciprocating instruments have short lifespan, thus manufacturers recommend using one file per tooth. Reciprocating instruments are recommended for less experienced dentist.

No abstract

Background: The purpose of this study was to compare the cyclic fatigue resistance of newly developed TruNatomy instruments (TRN) in single and double (S-shaped) curvature canals with HyFlex CM (HCM), Vortex Blue (VB) and RaCe (RC) instruments. Methods: Size 20/.04 taper and size 25/0.04 of HCM, VB and RC were used. For TRN instruments, size 20/.04 taper (small) and size 26/.04 taper (prime) were used. The instruments were tested in artificial canals with double curvature (coronal curve; 60° curvature, 5 mm radius and apical curve; 70° curvature and 2 mm radius) and single curvature (60° curvature, 5 mm radius). The number of cycles to failure (NCF) was recorded. Data were statistically analyzed by Kruskal-Wallis and Dunn’s multiple comparison tests. Weibull analysis was performed on NCF data. Statistical significant was set at p < 0.05. Results: TRN and HCM revealed higher NCF compared with the other instruments for both tested sizes in single and double curvature canals ( p < 0.05). TRN and HCM showed no statistically significant difference in the NCF ( p > 0.05). The probability of survival was higher for HCM and TRN instruments than VB and RC instruments. Conclusions: HCM and TRN instruments were more resistant to cyclic fatigue than VB and RC instruments in single and double curvature canals. HCM and TRN instruments were anticipated to survive with higher number of cycles than the other tested instruments. RC instrument had the lowest fatigue resistance than the other instruments.

Background To evaluate the effect of surface treatments on the push-out bond strength of Biodentine (BD) and white mineral trioxide aggregate (WMTA) to fiber posts. Methods Two brands of fiber posts were used: Reblida post; RP and RelyX post; RX. Each type of post (n = 80/group) was divided into four groups (n = 20/group) and exposed to surface treatment as follows: Control (no treatment), sandblasting (SB), hydrofluoric acid (HF), and TiF4 4 wt/v%. Each group was further subdivided into two subgroups (n = 10/subgroup) based on the type of CSCs used as follows: Subgroup A: BD and Subgroup B: WMTA. Push-out bond strength of BD and WMTA to glass fiber posts was assessed. Data were statistically analyzed using three-way ANOVA and Tukey’s test. A Weibull analysis was performed on the push-out bond strength data. Results BD showed higher bond strength than WMTA (P < 0.001). The push-out bond strength for posts treated with TiF4 4 wt/v% showed greater bond strength than the other surface treatments (P < 0.05). The BD/RP-TiF4 4 wt/v% showed the greater characteristic bond strength (σ0) (15.93) compared with the other groups. Surface treatments modified the surface topography of glass fiber posts. Conclusions The BD/RP-TiF4 4 wt/v% showed greater bond strength compared with the other groups. The TiF4 4 wt/v% surface treatment enhanced the bond strength of BD and WMTA to glass fiber posts than the other treatments. Surface treatment of fiber post with TiF4 4 wt/v% could be used to improve the bond strength with calcium silicate-based cements.