The transverse (t-) tubules of cardiac ventricular myocytes are invaginations of the surface membrane that form a complex network within the cell. Many of the key proteins involved in excitation-contraction coupling appear to be located predominantly at the t-tubule membrane.Despite their importance, the fraction of cell membrane within the t-tubules remains unclear: measurement of cell capacitance following detubulation suggests ~32%, whereas optical measurements suggest up to ~65%. We have therefore investigated the factors that may account for this discrepancy. Calculation of the combinations of t-tubule radius, length and density that produce t-tubular membrane fractions of 32% or 56% suggest that the true fraction is at the upper end of this range. Assessment of detubulation using confocal and electron microscopy suggests that incomplete detubulation can account for some, but not all of the difference. High cholesterol, and a consequent decrease in specific capacitance, in the t-tubule membrane, may also cause the ttubule fraction calculated from the loss of capacitance following detubulation to be underestimated. Correcting for both of these factors results in an estimate that is still lower than that obtained from optical measurements suggesting either that optical methods overestimate the fraction of membrane in the t-tubules, or that other, unknown, factors, reduce the apparent fraction obtained by detubulation. A biophysically realistic computer model of a rat ventricular myocyte, incorporating a t-tubule network, is used to assess the effect of the altered estimates of t-tubular membrane fraction on the calculated distribution of ion flux pathways.

This study elucidates the charge transport processes of polyaniline (PANI) composite membranes and correlates them to the PANI deposition site and the extent of PANI surface layering on the base microporous membranes. PANI was deposited either as a surface layer or inside the pores of cellulose acetate microporous membranes using various in situ chemical polymerization techniques. The extent of PANI layering at the surface of the base membrane and its oxidation and doping states were characterized using Fourier transform infrared (FTIR) spectroscopy and X-ray photoelectron spectroscopy (XPS). PANI deposition on the membranes showed a strong dependence on the polymerization technique and polymerization time within a single technique. In XPS, the deconvolution of C 1s and N 1s core-level spectra of the composite membranes was used to quantify the extent of PANI layering at the surface along with its oxidation and doping states. PANI incompletely covered the surface of the base microporous membranes for all the employed techniques. However, the extent of the layering increased with the polymerization time in a particular technique. The charge transport through the bulk membrane and charge transfer at the membrane/electrode interface were studied by electrochemical impedance spectroscopy (EIS). The data were analyzed using the equivalent circuit modeling technique. The modeling parameters revealed that PANI deposition at the surface enhanced the interfacial charge transfer but the process depended on the extent of the surface coverage of the membrane. In addition, the charge transport in the bulk membrane depended on the PANI intercalation level, which varied depending on the polymerization technique employed. In addition, the EIS of electrolyte-soaked membranes was also conducted to evaluate the effects of PANI deposition site on charge transport in the presence of an electrolyte. PANI layering at the pore walls of the base membrane from diaphragmatic polymerization in a two-compartment cell showed that charge transport processes were strongly affected by the interaction of the electrolyte with the PANI layer at the pore surface. This study successfully showed the dependence of charge transport mechanisms of PANI composite membranes on the PANI deposition site and extent of surface layering at the membrane surface.

No abstract

Polyaniline (PANI) can be deposited either on the surface or in the bulk of a microporous membrane by various chemical oxidative polymerization techniques. Each technique has distinctive effects on the PANI site and extent of deposition on the base membrane. In the present study, mixed cellulose ester (ME) membranes with tortuous pore morphology were used as base membranes. The chemical oxidative polymerization techniques employed, included polymerization using an in-house-built two-compartment permeation cell. The resultant composite membranes have been characterized by scanning electron microscopy (SEM), Fourier-transform infrared spectroscopy (FTIR-ATR), and electrical conductivity measurements. The results showed that PANI was layered on the pore walls of the membrane using two-compartment permeation cell. Vapor-phase polymerization yielded a surface layer of PANI with little deposition in the bulk. A distorted PANI surface layer was achieved by solution-phase (dip) polymerization. Moreover, asymmetric PANI deposition within the membrane bulk was evidenced using two-compartment permeation cell. Composite membranes synthesized using two-compartment cell showed highest levels of conductivity (approximately 10(-2) S/cm) as compared to the membranes modified by single-step solution-phase polymerization. FTIR-ATR results indicated the extent of PANI coating and its oxidation state which was identified as doped emeraldine PANI, from all the employed techniques. Asymmetric deposition and extent have been explained in terms of the physical and chemical reaction steps involved in the heterogeneous aniline polymerization reactions in the two-compartment cell technique.

In order to enhance salt rejection level and high pressure mechanical integrity, functionalized nanokaolin decorated multiwall carbon nanotubes (FNKM, 0–5 wt % loading) were incorporated into a cellulose acetate (CA) matrix using high temperature solution mixing methodology. Scanning electron microscopy (SEM), X-ray diffraction technique (XRD), thermo-gravimetric analyzer (TGA) and Fourier transform infrared spectrometer (FTIR) were used to characterize the prepared membranes. The obtained results revealed that with increasing FNKM concentration in the host polymeric matrix, composite membrane’s structural, functional, thermal, water permeation/flux and salt rejection characteristics were also modified accordingly. Percent enhancement in salt rejection was increased around threefold by adding 5 wt % FNKM in CA.

Polyaniline was deposited on polystyrene sulfonated divinyl benzene resin by varying polymerization time to fabricate heterogeneous PVC matrix membranes.

No abstract

No abstract