Resumen: Fibra de Retamo Liso (telinemonspessulana) fue mezclada en una matriz polimérica formada por: polietileno de baja densidad (LDPE) y poliestireno de alto impacto (HIPS) en relación 70:30 respectivamente. La fibra natural fue sometida a reducción de tamaño entre 1700 y 850 µm; se le realizó tratamiento superficial de mercerización; el contenido de humedad fue 0,17%. El análisis termo gravimétrico (TGA) muestra que la fibra tratada tiene estabilidad de 200,53 °C. La elaboración del compuesto se realizó en mezclador interno y la técnica de obtención de las probetas fue mediante moldeo por compresión. Se evaluó el efecto del agente entrecruzante peróxido de dicumilo (DCP) en compuestos con varios porcentajes de fibra: 0; 10; 25; 50 phr. La adición de DCP (1 phr) en los compuestos, mejora significativamente las propiedades de tensión con respecto a similares concentraciones de fibra; sin embargo, esta diferencia en los valores de las propiedades disminuye progresivamente cuando la cantidad de fibra se aproxima a 50 phr. El aumento en la concentración de fibra afecta negativamente las propiedades de tensión, con excepción del Módulo de Elasticidad y la Resistencia a la Fluencia. La causa principal es originada por la baja adhesión interfacial fibra natural-matriz polimérica, claramente evidenciada en las imágenes SEM. Palabras-clave: TelineMonspessulana, compuesto de plástico y madera (WPC), polietileno de baja densidad, poliestireno de alto impacto, peróxido de dicumilo. Abstract: Straight Retamo Fiber (telinemonspessulana) was mixed in a polymer matrix formed by low density polyethylene (LDPE) and high impact polystyrene (HIPS) in a 70:30 ratio. The natural fiber was subjected to size reduction between 1700 and 850 µm; surface treatment mercerization was performed; the moisture content was 0.17%. The thermo gravimetric analysis (TGA) showed that the treated fiber has stability at 200.53 °C. The preparation of the compound was performed in an internal mixer with the samples being obtained by compression molding. The effect of crosslinking agent was evaluated: dicumyl peroxide (DCP) in compounds with various percentages of fiber: 0; 10; 25; 50 phr. The addition of DCP (1 phr) in the compounds significantly improved tensile properties compared to similar concentrations of fiber; however, this difference in property values progressively decreased when the amount of fiber approximated 50 phr. The increase in fiber concentration negatively affected the tensile properties, except for the modulus of elasticity and fluence resistance. The main cause is the low interfacial adhesion between the natural fiber and the polymer matrix, clearly evidenced in the SEM images.
Palabras clave: biocombustibles, transesterificación, propiedades térmicas, flujo en frío RESUMEN La investigación consistió en analizar el potencial de la oleorresina extraída del árbol Copaifera reticulata para la producción de biodiésel a partir del proceso de transesterificación. La caracterización incluyó el estudio de la fluidez a bajas temperaturas, la estabilidad oxidativa y la determinación de propiedades como viscosidad, índice de acidez y de fluidez, humedad, y punto de inflamación de la oleorresina tanto cruda como modificada por vía química. Se observó que la técnica empleada para la producción de biodiésel genera pérdidas de oleorresina, ya que el rendimiento global en la producción fue cercano al 10 %. Sin embargo, los procesos de refinado y transesterificación influyeron positivamente sobre la estabilidad oxidativa de la oleorresina. Respecto de la oleorresina cruda, la estabilidad de la oleorresina refinada y el biodiésel de copaiba se incrementaron en 46 y 47 ºC, respectivamente. De acuerdo con los puntos de fluidez, en todos los casos el comportamiento de flujo en frío supera significativamente los rangos establecidos. El biodiésel presentó un punto de fluidez inferior a-39 ºC. Según los valores de viscosidad y densidad, el uso de la oleorresina en sus formas cruda o modificado-aunque condicionado de forma directa-podría considerarse en mezclas con gasóleo u otros biocombustibles, a fin de mejorar sus propiedades a bajas temperaturas. Estudios posteriores permitirán establecer técnicas eficientes para la modificación química de la oleorresina.
Introduction Corrosion of concrete rebar has been established as the main factor of the premature deterioration of reinforced concrete structures. The occurrence of such phenomena represents mostly the durability problems of the material, especially when the structure is subjected to the chloride ions presence (in marine or high salinity enviroment) and large amounts of carbon dioxide (CO2 ), processes known as chloride penetration and carbonation respectively[1,2,3]. Once the corrosión process has appeared in rebar, these begin to generate large stresses on the layer of concrete around them (due to the iron oxides that accumulate around the transversal area) which over time can generate microcracks, cracks and failure on the general structure[4]. Given the importance of preserving civil structures, is evident the strong necessity of obtaining a system with great flexibility to perform the estimation in situ of the corrosive state, capable to dispose the information for immediate consultation anywhere with minimum internet access. Therefore, the present work shows the development and implementation of a system for in situ monitoring of corrosion, for any reinforced concrete structure based on ASTM C876-91[5] standard for measuring half-cell potential, with which it is possible to determine the corrosion probability of rebar in reinforced concrete structures. Also, the equipment performance is presented by using different reference electrodes as Copper / Copper Sulfate (Cu -CuSO4 ), silver / silver chloride (Ag / AgCl) and Zinc / Zinc Sulfate (Zn -ZnSO4 ). Experiments and Results It was obtained a system for in situ monitoring of corrosion for reinforced concrete, that allows to estimate the corrosion probability on rebar, where the user send a text message, to start the test in the system and in return, via GPRS (General Packet Radio Service), the equipment disposes the data trend on a graphic trough a web server on an internet domain (figure 1). The system was tested on a building of the University complex, where its performance was evaluated using three different reference electrodes, obtaining an error over the measurement, between the standard and the system, of 6.62% (figure 2). References (1) ROA-RODRIGUEZ, G., APERADOR, W., DELGADO, A. Calculation of Chloride Penetration Profile in Concrete Structures. International Journal of Electrochemical Science. v. 8, p. 5022-5035, Apr. 2013 (2) HA WONG, S., VELI, S. Corrosion Monitoring of Reinforced Concrete Structures - A Review. International Journal of Electrochemistry Science, v. 2, p. 1 – 28, Jan. 2007. (3) SATHIYANARAYANAN, S., PANJALI NATARAJAN, K., SARAVANAN, S., SRINIVASAN, G. Corrosion monitoring of steel in concrete by galvanostatic pulse technique. Cement & Concrete Composites, v. 28, p. 630-637, May. 2006. (4) SHAMSAD, A., Reinforcement corrosion in concrete structures, its monitoring and service life prediction––a review. Cement & Concrete Composites, v. 25, p. 459 – 471, May. 2003 (5) ASTM Standard C876-09, 1991, Standard Test Method for Corrosion Potentials of Uncoated Reinforcing Steel in Concrete. ASTM International, West Conshohocken, PA, 2003, DOI: 10.1520/C0876-09.
El presente artículo busca llevar a cabo un análisis teórico del comportamiento de las principales propiedades del biodiesel (densidad, viscosidad, poder calorífico, capacidad calorífica, gravedad API), empleando para ello datos de la normatividad técnica mundial asociada a su producción, así como datos teóricos definidos en la literatura. A partir del análisis de las propiedades se genera una evaluación de los biodiesel en términos de su comportamiento y calidad. El desarrollo se llevó a cabo mediante la simulación de los procesos en Matlab, obteniendo un conjunto de parámetros base para la evaluación de todo biodiesel. Esta investigación emplea métodos estadísticos descriptivos, de muestreo, así como de correlación y, métodos matemáticos como mínimos cuadrados, aplicaciones lineales y exponenciales, entre otros para generar el análisis conjunto de la información, así como de los modelos empleados, logrando un mayor grado de confianza en los análisis. Los datos resultantes de la simulación para las propiedades fisicoquímicas consideradas son cercanos a los valores experimentales reportados en la bibliografía, lo que permite su uso, reduciendo los tiempos en estudios en biocombustibles.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.